EINHELL 44.661.54 Instructions D'origine page 23

Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The equipment has to be set up where it can
stand securely.
•
Before starting work, firmly screw the grin-
ding/sanding machine to the workbench or
equivalent using the 4 mounting holes (8) in
the base plate (9).
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the grinding/sanding
wheel to run freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
Anl_TC-US_350_SPK9.indb 23 Anl_TC-US_350_SPK9.indb 23
GB
5.1 Assembling the spark defl ector / safety
window (Fig. 3/4)
•
Fasten the spark deflector (3) to the machine
(Fig. 3).
•
To do this, use the socket head screws (11),
washers (12), spring washers (13) and nuts
(14).
•
Tighten the screw connection using a 4 mm
hex key and an 8 mm wrench. Note! Not
supplied.
•
Fit the safety window (2) to the spark deflec-
tor (3) using a lock screw (15), a washer (12),
a spring washer (13) and a locking button
(16) (Fig. 4).
5.2 Adjusting the spark defl ector (Fig. 5)
•
With the help of the slots in the spark deflec-
tor (3) you can adjust it in vertical direction.
•
To do so, slacken the socket head screws
(11) and push the spark deflector as close as
possible to the grinding/sanding wheel (5).
•
Warning! The distance between the grinding/
sanding wheel (5) and the spark deflector (3)
must be set as small as possible and under
no circumstances should it exceed 2 mm.
•
Then secure the spark deflector (3) again.
•
Warning! Adjust the spark deflector (3) peri-
odically to compensate for wear on the grin-
ding/sanding wheel (5).
5.3 Fitting the workpiece support (Fig. 6a)
•
Fit the workpiece support (7) to the machine.
•
Warning! The angled face of the workpiece
support must point away from the grinding/
sanding wheel (5)!
•
To achieve this, use the lock screw (17), the
washer (18), the spring washer (19) and the
locking button (20).
5.4 Fitting the workpiece support for the grin-
ding/sanding belt (Fig. 6b/6c)
•
The workpiece support (10) can be screwed
tight in two different positions to suit the work-
piece you want to work on.
•
If you want to grind/sand a larger surface, fit
the workpiece support (10) as shown in Fig.
6b.
•
For grinding/sanding work on narrow sur-
faces, for example, or for chamfering edges
or grinding/sanding curves, you can fit the
workpiece support (10) as shown in Fig. 6c.
•
To do this, use the lock bolt (17), washer (18),
spring washer (19) and locking knob (20).
- 23 -
25.06.2020 12:20:50 25.06.2020 12:20:50