EINHELL 44.661.54 Instructions D'origine page 22

sanding wheels or belts which are suitable for it
and comply with the characteristic data in these
instructions.
The machine is allowed to be used only for its
intended purpose! Even when the equipment is
used as prescribed it is still impossible to elimina-
te certain residual risk factors. The following ha-
zards may arise in connection with the machine's
construction and layout:
•
Contact with the grinding wheel where it is not
covered.
•
Catapulting of parts from out of damaged
grinding wheels.
•
Catapulting of workpieces and parts of work-
pieces.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
•
The rotating parts of the device cannot be
covered for functional reasons. Therefore you
must exercise care and hold the workpiece
firmly to prevent it slipping which could result
in your hands coming into contact with the
grinding/sanding belt.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
4. Technical data
Rated voltage: ........................ 220-240 V ~ 50 Hz
Power rating: ......... S1 185 W | S2 30 min 350 W
Idle speed n : ......................................2980 min
0
Grinding/sanding wheel diameter: ......... 150 mm
Grinding/sanding wheel thickness: ........... 20 mm
Grinding/sanding wheel hole diameter: .... 32 mm
Grinding/sanding wheel grit size: .................. K36
Circumferential speed: ...........................23.4 m/s
Belt speed: ..........................................900 m/min
Grinding/sanding belt dimensions ... 50 x 686 mm
Grinding/sanding belt grit size: ...................... K80
Anl_TC-US_350_SPK9.indb 22 Anl_TC-US_350_SPK9.indb 22
GB
Protection class ................................................. I
Weight .......................................... approx. 8.5 kg
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (350 W)
for no longer than the time stipulated on the spe-
cifi cations label (30 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
Operation
L sound pressure level ..................... 88,6 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ..................... 101,6 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
-1
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
- 22 -
25.06.2020 12:20:50 25.06.2020 12:20:50