Enduro EM515FL Manuel De L'utilisateur page 57

TROUBLE SHOOTING
Should your manoeuvring system fail to operate, please check the following:
System fails to operate, does not function at all:
Make sure that the battery power isolation switch (33) is turned on.
Check the cable-connection between the caravan battery and the control unit.
Check the fuse (Fig. 10) in the red positive battery cable. If the fuse is blown, it must be replaced with a fuse of
the same value (100A). Never "bridge" the fuse (if needed contact your EN ® supplier). To replace the fuse,
DURO
first disconnect the positive (+) power cable from the battery. Than release the mounting screws that hold the
fuse (Fig. 10A), replace the fuse (Fig. 10B), and finally tighten the screws securely. Close the housing of the
fuse and connect the positive (+) power cable again to the battery. The system is ready again for use.
Check the batteries of the remote handset. If empty, replace the 1,5 Volt batteries (Fig. 9).
Caravan battery could be empty. If empty, recharge completely or renew caravan battery before taking any
further action.
Caravan battery could be overloaded. Check your charging equipment and try to discharge the battery by
connecting/using a light or any other load. If this does not give any result, renew caravan battery before taking
any further action.
Check the distance between the remote handset and the caravan is not more than 5 metres. If there is no
signal between the remote handset and the control unit, the manoeuvring system will not function at all and
the communication icon on handset is blinking.
Check if there is any distortion signal (other transmitter, high power cables, Wifi etc.) that disturbs a good
communication between remote handset and control unit. If there is no good communication between the
control unit and remote handset, the manoeuvring system will not function and the communication icon on
remote handset is blinking.
In general, all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the manoeuvring system via the isolation switch and the
remote handset for at least 15 seconds and then turn them on again.
System fails to operate or moves intermittently:
Check the batteries of the remote handset. If empty, replace the 1,5 Volt batteries (Fig. 9).
Caravan battery could be empty. If empty, recharge completely or renew caravan battery before taking any
further action.
Caravan battery could be low - with the rollers engaged. Check the voltage drop on the caravan battery, if this
drops well below 10 volts, charge or renew caravan battery.
Caravan battery could be overloaded. Check your charging equipment and try to discharge the battery by
connecting/using a light or other load. If this does not give any result, renew caravan battery before taking any
further action.
Check the cable-connection between the caravan battery and the control unit.
Badly connected or corroded battery terminals can cause intermittent problems, check battery terminals, clean
and connect again.
Check the distance between the remote handset and the caravan is not more than 5metres. If there is no signal
between the remote handset and the control unit, the manoeuvring system will not function at all and the
communication icon on handset is blinking.
Check if there is any distortion signal (other transmitter, high power cables, Wifi etc.) that disturbs a good
communication between remote handset and control unit. If there is no good communication between the
control unit and remote handset, the manoeuvring system will not function and the communication icon on
remote handset is blinking.
In general, all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the manoeuvring system via the isolation switch and the
remote handset for at least 15 seconds and then turn them on again.
Roller will not turn, spindle rotates freely:
The motor or gear is broken, please contact your EN ® supplier.
DURO
In case of any doubt, please call your EN ® supplier.
DURO
EN ® EM515FL 47
DURO
Ref: EM515FL-UM-TKI-0323-Rev.B.