EINHELL 34.047.00 Mode D'emploi page 23

Anleitung_GC_PM_46_1_51_1_S_HW_BS_SPK7__ 21.10.13 14:13 Seite 23
G-PM 51/1 S HW B&S
Engine type:
Single cylinder four-stroke engine, 150 ccm
Engine output (2800 min -1 ):
Working speed n 0 :
Fuel:
Cutting height adjustment:
Cutting width:
Weight:
Sound and vibration
L pA sound pressure level
K pA uncertainty
L WA sound power level
L WA sound power (measured)
K WA uncertainty
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration emission value a = 5.9 m/s
h
K uncertainty = 2.4 m/s 2
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
6. Before starting the equipment
6.1 Assembling the components
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can
A funnel (suitable for the tankʼs petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
2.22 kW/3.02 hp
Assembly
2800 min -1 1. Fasten the push bar (Fig. 3a/Item 5) using one
screw (Fig. 3a/Item 15) and one star nut (Fig.
standard petrol
3a/Item 12) on each side. For fastening choose
central, (25-85 mm)
one of the holes to suit the required height of the
510 mm
push bar. Important: The identical height must be
40 kg set on both sides. Make sure that the cables
which are fastened later are not in the way.
2. Fasten the top push bar to the bottom push bar
using a screw (Fig. 3b/Item 16) and a star nut
90 dB(A)
(Fig. 3b/Item 12) on each side.
3 dB
3. Insert the grip of the starter cable (Fig. 3c/Item 4)
98 dB(A)
into the hook provided for that purpose as shown
92.9 dB(A)
in Fig. 3c.
5.1 dB 4. Fasten the cables to the push bar with the
supplied cable clips (Fig. 3d/Item 13).
5. Lift the ejector flap (Fig. 4a/Item 8) with one hand
and hook in the grass bag (Fig. 4a/Item 7) as
shown in Fig. 4a.
2
6.2 Setting the cutting height (Fig. 15-16)
Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
(Fig. 7/Item 9). Up to 5 different cutting heights
can be selected.
Pull the adjuster lever out and select the desired
cutting height. The lever will snap into the desired
position.
7. Operation
Note:
For detailed information on starting the engine,
refer to the enclosed manual from Briggs &
Stratton.
Important.
The engine does not come with oil in it.
GB
23