Citizen JCTV3241X Manuel D'instructions page 6

ANTENNA/CATV CONNECTIONS
Combination VHF/UHF Antenna
Single 75 ohm Cable
300 ohm Twin-lead Wire
Take off the Splitter
Splitter
UHF Antenna
300 ohm Twin-lead Wire
VHF Antenna
Single 75 ohm Cable
300 ohm Twin-lead Wire
Incoming CATV
Converter/ Descrambler
Converter/ Descrambler
Splitter A / B Switch
Combination VHF/UHF Antenna (Single 75 ohm Cable or 300
ohm Twin-lead Wire)
Connect the 75 ohm cable from a combination VHF/UHF antenna to
the Antenna Jack. If your combination antenna has a 300 ohm Twin-
lead Wire, use the 300-75 ohm Matching Transformer (not supplied).
Combination VHF/UHF Antenna (Separate VHF and UHF 300
ohm Twin-leads)
Connect the UHF Twin-lead Wire to a Combiner (not supplied).
Connect the VHF Twin-lead to the 300-75 ohm Matching
Transformer (not supplied). Attach the Transformer to the Combiner.
Attach the Combiner to the Antenna Jack.
AUDIO/VIDEO JACK CONNECTIONS
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features
of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.
The connection diagrams below are offered as suggestions. You may need to modify them to accommodate your particular assortment
of components. The diagrams are intended to show component video and audio interconnections only.
Press the TV/AV selector button to select the AV mode to use the TV as a monitor.
TV/AV SELECTION
If you connect the TV to a VCR, camcorder, Video game System
or other A/V component, through the audio/video in jacks, use the
TV/AV button to make your selection.
Press the TV/AV button repeatedly to select the desired mode.
"AUX1" or "AUX2" will display on the screen for 4 seconds.
TV AUX 1
1. To connect the TV to a VCR
Set the TV/AV SELECTION for this connection, to AUX1.
VCR
To Audio/Video
OUT
6
300-75 ohm
Matching Transformer
(not supplied)
Combiner
(not supplied)
300-75 ohm
Matching Transformer
(not supplied)
A B
AUX 1
AUX 2
Rear of TV
VIDEO
OUT IN
VIDEO
ANT.
L
(MONO) S-VIDEO
AUDIO
R
AUDIO (L)
AUDIO (R)
(not supplied)
Separate VHF/UHF Antennas
Connect the 75 ohm Cable from the VHF antenna and the UHF
antenna Twin-lead to a combiner (not supplied). Attach the Combiner
to the Antenna Jack.
NOTE: If your VHF antenna has a Twin-lead Wire, use the 300-75
ohm Matching Transformer (not supplied), then connect the
Transformer to the Combiner.
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler box,
connect the CATV 75 ohm Coaxial Cable directly to the Antenna
Jack on the back of the television.
For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service which requires the use of a
Converter/Descrambler box, connect the incoming cable to the
Converter/Descrambler box and connect the output of the box to the
Antenna Jack on the back of the television. Follow the connections
shown left. Set the television to the output of the Converter/
Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to select channels.
For Subscribers to Unscrambled Basic Cable with Scrambled
Premium Channels
If you subscribe to a cable service in which basic cable channels
are unscrambled and premium channels require the use of a
Converter/Descrambler box, you may wish to use a two-set signal
splitter (sometimes called a "two-set coupler") and an A/B Switch
box from the cable installer or an electronics supply store. Follow
the connections shown left. With the switch in the "B" position, you
can directly tune any nonscrambled channels on your TV. With the
switch in the "A" position, tune your TV to the output of the Converter/
Descrambler box (usually channel 3 or 4) and use the box to tune
scrambled channels.
2. To connect the TV to a Video Game System
Set the TV/AV SELECTION for this connection, to AUX2.
The TV can also be used as a display device for many video
game systems. However, due to the wide variety of different
types of signal generated by these devices and subsequent
hook-up variations required, they have not all been included
in the suggested connection diagrams. You'll need to consult
each component's Owner's Manual for additional information.
To Audio/Video OUT
TV GAME
(not supplied)
3. To connect the TV to the Camcorder
Set the TV/AV SELECTION for this connection, to AUX2.
To playback from the camcorder, connect the camcorder to the
TV as shown.
To AV OUT jack
This television has an extended
tuning range and can tune most
cable channels without using a
cable company supplied
converter box. Some cable
companies offer "premium pay
channels" in which the signal is
scrambled. Descrambling these
signals for normal viewing
requires the use of a descrambler
device which is generally
provided by the cable company.
Front of TV
VIDEO IN (MONO) L – AUDIO IN – R PHONES
Front of TV
VIDEO IN (MONO) L – AUDIO IN – R PHONES
(not supplied)