Publicité
Les langues disponibles
Les langues disponibles
the belt tracking adjustment knob
the belt runs outward, turn the tracking adjustment knob
clockwise to make the belt run inward. If belt runs inward,
turn the tracking adjustment knob counterclockwise to make
the belt run outward.
Belt life will be greatly increased by keeping the tracking
adjustment set properly. To prevent the sanding belt from
rubbing against the sander housing, keep the edge of the
belt about 7/64" (2.7 mm) to 13/64" (5.1 mm) from the cover
side of housing.
Changing The Sanding Belt (Fig. F, G)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: To reduce the risk of injury, make sure belt
is installed with arrows in proper direction of rotation.
Failure to do this could result in the belt unraveling
creating a hazardous condition.
Pull the quick release lever
the tension on the sanding belt. Pull the sanding belt
from the two rollers. Put the new 3" x 18" (75 mm x 457 mm)
sanding belt in position on the front and rear rollers
(Figure G). Ensure that the arrows on the sanding belt and on
your belt sander are pointing in the same direction. Use one
hand to hold the unit and use the other hand to push the
lever to the rear to tension the sanding belt.
Dust Extraction (Fig. H)
WARNING: Risk of dust inhalation. To reduce the
risk of personal injury, ALWAYS wear an approved
dust mask.
A dust exhaust port
is supplied with your tool.
8
The dust exhaust port allows you to connect the tool to an
external dust extractor, either using the AirLock™ system, or a
standard 32 mm dust extractor fitment.
WARNING: ALWAYS use a vacuum extractor designed
in compliance with the applicable directives regarding
dust emission when sanding wood. Vacuum hoses of
most common vacuum cleaners will fit directly into the
dust extraction outlet.
Fitting and Removing the Dustbag (Fig. I)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: Fire hazard. Collected sanding dust from
sanding surface coatings (polyurethane, linseed oil,
etc.) can self‑ignite in sander dust bag or elsewhere
and cause fire. To reduce risk, empty bag frequently
and strictly follow sander manual and coating
manufacturer's instructions.
7
to center the belt. If
shown in Figure F to release
4
WARNING: Fire hazard. When sanding wood that
could contain nails, or when sanding metal surfaces,
do not use the dust bag or a vacuum cleaner because
sparks are generated. Wear safety glasses and a dust
mask. Due to the danger of fire, do not use your belt
sander to sand magnesium surfaces. Do not use for
wet sanding.
When using your belt sander, dust and grit are produced.
It is important to use a dust bag. Connect the dust bag
by sliding the plastic opening of the bag down over the
dust exhaust port
bag, remove it from the sander and unzip the bag over a
trash container.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. J)
1
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
5
and one hand on the three position handle
Trigger and Lock‑On Button (Fig. A, K, L)
To start your belt sander, depress the trigger
in Figure L. To stop your belt sander release the trigger.
For continuous operation, depress trigger then depress
the lock‑on button
the trigger. To stop your belt sander, depress the trigger to
release the lock‑on button. Release the trigger.
8
of the sander. To empty the dust
into the tool handle, align
10
11
and firmly pull the
3
, as shown in Figure K, and release
English
13
6
.
2
as shown
11
Publicité
