Publicité
Les langues disponibles
Les langues disponibles
English
Car compressor
Intended Use
This product is used for inflation of tires, balls, inflatable
air beds, bicycle tires, etc. The car compressor is equipped
with a manometer and an adaptor for connection to the
car cigarette lighter.
Technical specifications
Car system voltage, V
Power, W
Discharge, litres per min.
Idling speed, rpm
Maximum output pressure,
bar (Pa)
Weight, kg
GENERAL REQUIREMENTS
• Do not leave the car compressor in the rain and snow.
• Do not use the product in highly humid environment.
• Do not work near inflammable liquids and gases.
• Do not let children operate the car compressor.
• Keep in a dry and closed place out of reach of children.
• Do not overload the product. Failures caused by over-
load are not covered by conditions of free warranty
repair.
• Use only for the purpose specified.
• Control operability of the air hose.
• It is prohibited to move the compressor holding it by the
power cable.
• Avoid contact of the hose with oil and sharp objects.
• Avoid overheating of the hose.
• Keep your balance while working.
• Keep the compressor clean. Clean it regularly from oil
stains.
• Disconnect the compressor from the car system voltage
in the following cases:
- The product is not in use.
- During maintenance operations.
- During replacement of parts and mechanical units.
• Be attentive and collected while working.
• Refrain from work, if you are tired or ill.
• Regularly check the product for damages and failures.
• If any defects are detected, contact the service center
• For failure avoidance, do not use spare parts of other
manufacturers.
To prevent failures
• Keep the compressor adapter clean. With the compres-
sor connected to the car cigarette lighter, in case of
short circuit, a life-threatening situation may occur. Ac-
cumulator capacity is very high, so you can get injured.
• Protect the compressor from overheating. Do not cover
the compressor with foreign objects while in use.
12
120
25
3400
7 (700000)
1,8
Before connecting, please check
• If the adapter and the car lighter socket match;
• If the car accumulator voltage matches with the com-
pressor's characteristics;
• If the accumulator can provide 10 A;
• Absence of failures and breakdowns in the cable and the
adapter for the cigarette lighter.
OPERATION
• First, check pressure in the inflated object. It can be
done with the manometer, installed in the compressor.
Just connect the hose of the idle compressor to the
inflated object.
• Avoid excessive pressurization.
• Do not place the working compressor in the car com-
partment.
• Do not leave the working compressor unattended.
• Switch off the compressor immediately in the following
cases:
1. If the adapter or power cable is damaged;
2. Smell of burning insulation appears.
ATTENTION! This compressor is intended for short-time
operation (not more than 10 minutes). Longer operation
of the compressor may cause its overheating and break-
down. If you need to use the compressor longer, after first
10 minutes switch off the device and let it cool down for
10 minutes before restart.
Inflation of car tires
• Place the car to ensure the lowest position of the tire
valve.
• Connect the nipple to the tire valve. Push the lever
down and fix the nipple.
• Check pressure with the manometer.
• Connect the compressor to the car lighter socket.
• When the required pressure level is reached, disconnect
the compressor from the car lighter socket.
• Release the lock of the joining nipple and remove it
from the valve.
Inflation of balls and toys
• Install the valve adapter (connector or needle for ball
inflation) on the nipple and latch the lock by pushing
the lever down.
• Connect the air hose with the adapter to the inflated
object.
• Connect the compressor to the car lighter socket.
• Turn the compressor on.
• When the required pressure level is reached, disconnect
the compressor from the car lighter socket.
• Disconnect the air hose with the adapter from the in-
flated object.
• Quickly close the air passage of the inflated object.
ATTENTION! Control air pressure in the inflated object.
Avoid excessive pressurization of the inflated object.
5
Publicité
