Publicité
Les langues disponibles
Les langues disponibles
Stove state
Stove State
Below are given the steps for accessing the relative menu starting from Stand-By mode.
MENU
USER
MANUFACTURER'S
TECHNICIAN
Press the key
"access menu" to
access the
MENU page
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
PUMP
3-WAY VALVE HEAT
PRESSURE 1.1 BAR
SHUTDOWN
In this mode you can check the proper operation of the most important parameters of the appliance. Here is a list of real data of the
stove useful for service during inspection.
Stove state
- Circulator state (ON running)
- Position of 3-way valve DHW (domestic hot water) or HEAT (heating);
Flame temperature
- System pressure;
Temperature read by the handheld uit
- Stove state;
- Temperature read by the handheld unit;
Settings > Enable thermostat
- External thermostat (request ON);
- Flame temperature (combustion chamber);
Settings > Enable thermostat
- Combustion fume exhaust temperature;
- Inlet flow meter temperature;
DATE-TIME
- Heated flow meter temp.;
ENABLE EXT. T
SEASON
- Electronic board temperature;
CONTRAST
FW VERSION
LANGUAGE
ADJUST
To exit the STOVE STATE page and return to Stand-by page, press the button repeatedly.
Press the "enter" key
to access the
SETTINGS
Settings
ENABLE THERMOSTAT
Below are given the steps for accessing the relative menu starting from Stand-By mode.
MENU
USER
MANUFACTURER'S
TECHNICIAN
Press the key
"confirm"
to enable the function.
Press the key
"access menu" to
access the
Settings > Season
MENU page
DATE-TIME
After following the procedure above step by step, you can set the following functions:
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
Use and maintenance manual Vela 7-9
Manuale utente PALMARE IDRO TOUCH RADIO
CHRONOTHERMOSTAT
Press the key
"confirm"
to access the
USER page
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
g/min
RPM
POWER MOD
°C
T
Tsk
°C
Manuale utente PALMARE IDRO TOUCH RADIO
Press the key
"selection" to switch to
ENABLE THERMOSTAT.
CHRONOTHERMOSTAT
Press the key for several
times
to return to
Press the key
"STAND BY" page
"confirm"
to access the
USER page
Press the key
USER
POWER SETTING
SCREW LOADING
SET AIR-PELLET
Press the key
several times
to quickly switch to
Stove STATUS.
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
v
HH T ...
EXT.T ...
FLAME T 340°C
FUME T 120°C
F. EX. T 30°C
C. EX. T
55°C
EL B. T---25°C
- Current boiler power;
- Flow read by the flow meter;
- Fume extractor speed;
- Actual flow set;
- Boiler water temperature (SUPPLY);
- Boiler water temperature (optional) - RETURN from the system;
- Boiler DHW temperature;
- Puffer temperature - average warm point;
DATE-TIME
- Puffer temperature second reading (low temp.).
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
"confirm"
to access the function
In Stand-By mode, instead of room temperature measured
and settable, appears the line T ON if the room in which
the thermostat is installed has not reached the temperature
USER
requested or the writing T OFF if the temperature in the
POWER SETTING
room is reached.
SCREW LOADING
SET AIR-PELLET
Press the key
"selection" to switch to
second menu page
to the function
SETTINGS.
DATE-TIME
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
Rev.1 20.02.18
Page 67
EN
Vers. 01 del 07/04/15
Pag.30
USER
STOVE STATE
COMFROT CLIMA
SETTING
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
T. CALDERA
T.PUFFER H
T.PUFFER L
Vers. 01 del 07/04/15
Pag.31
ENABLE THERMOSTAT
USER
STOVE STATE
COMFROT CLIMA
SETTING
WINTER
SUMMER
Publicité
