Makita CL104D Manuel D'instructions page 10

6. Place the entire container part of the dust pack inside
the tool itself. (Fig. 14)
7. Close the front cover completely.
CAUTION:
• Install the dust stopper with the dust bag or dust pack
properly. Tool operation without proper installation of
them, or using broken or ripped one, it may allow dust
to get into the motor. This may result in motor failure.
• Do not fold the cardboard at its opening when installing
the paper pack.
• Never throw away the dust stopper because it needs to
be used repeatedly whenever either the dust bag or the
dust pack is used.
• The paper pack for the cleaner is an important
component for maintaining the tool performance. If you
use the other genuine paper pack, it may cause
smokes or ignition.
OPERATION (Fig. 20)
To connect attachments, such as nozzle, twist and insert
them to ensure secure connection during use. To
disconnect attachments, twist and remove them.
Cleaning (Suction)
Nozzle (Fig. 21)
Attach the nozzle to clean off tables, desks, furniture, etc.
Nozzle slips on easily.
Nozzle + Extension wand (Straight pipe) (Fig. 22)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for cleaning
a floor while standing erect.
Corner nozzle (Fig. 23)
Fit on the corner nozzle for cleaning corners and crevices
of a car or furniture.
Corner nozzle + Extension wand (Straight pipe)
(Fig. 24)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
Symptom
Weak suction power
Not working
014744
NOTE:
• Do not attempt to repair cleaner by yourself.
Disposing cleaner
A Li-ion battery is built into this cleaner. Always remove it
before disposing of the cleaner.
10
Area to be investigated
Is dust bag or paper pack full of dust?
Is dust bag clogged?
Is paper pack clogged?
Is battery cartridge exhausted?
Is battery cartridge exhausted?
After use
When storing the cleaner, hang it from a nail using the
hand strap. (Fig. 25)
NOTE:
• Putting the cleaner against the wall without any other
support cause the cleaner to fall down and be
damaged. (Fig. 26)
Cleaning (Fig. 27)
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/dust pack
mounting area and the dust stopper.
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Wash the dust bag in soapy water when it is clogged with
dust and the cleaner power becomes small. Dry it out
thoroughly before use. An insufficiently dried bag may
cause poor suction and shorten the service life of the
motor. (Fig. 28)
NOTE:
• Dust pack is a throw-away type.
When the sponge filter is clogged with dust, remove it
from the cleaner and then wipe it off or wash in water.
Removing and installing the sponge filter
To remove the sponge filter, remove the dust bag or dust
pack and then pinch and take it out. (Fig. 29)
Press in the whole edge of the sponge filter against the
recessed wall inside the dust bag/dust pack mounting
area. (Fig. 30)
CAUTION:
• After cleaning sponge filter, be sure to install it on the
cleaner. If washed in water, dry it up before installing.
An insufficiently dried sponge filter may shorten the
service life of the motor.
TROUBLE SHOOTING
Before asking for repairs, conduct your own inspection
first. If you find a problem that is not explained in the
manual, do not attempt to dismantle the tool. Instead, ask
Makita Authorized Service Centers, always using Makita
replacement parts for repairs.
Empty dust bag or paper pack.
Dust down or wash the dust bag.
Replace paper pack.
Charge the battery.
Charge the battery.
Removing built-in battery
CAUTION:
• Never remove the built-in battery from the cleaner
except when disposing of the cleaner. The battery will
be damaged or a battery short-circuit could result.
Fixing method