Profi Care PC-VL 3111 LB Mode D'emploi page 54

2. Connect the appliance to a duly installed protective
contact socket. The indicator lamp POWER shows that
the power supply is connected.
Fitting Batteries into the Remote Control
(Batteries not supplied.)
1. Open the lid of the battery compartment on the rear of
the remote control.
2. Insert 2 MICRO batteries of type R03 "AAA" 1.5 V.
3. Please ensure the correct polarity. Details can be found
in the battery compartment.
4. Close the battery compartment.
Remote Control Range
The remote control has a range of ca. 8 metres. If this range
becomes shorter, the batteries must be changed.
• To use the remote control, point it at the sensor on the
front of the switch housing.
• Make sure there are no obstacles between the remote
control and the sensor.
• The angle of the remote control to the remote control
sensor should not exceed 30 ° to the right, left, up, and
down.
Position
• The ideal position is a non-slip, flat surface.
• Do not place the appliance onto wood, to avoid deforma-
tion due to moisture.
• Watch out for electrical devices close by. They must not
get wet.
• Keep a distance of 2 metres from electrical equipment
and delicate furniture to protect these from moisture.
Assembly Instructions
The appliance must be fully assembled before use! We
recommend that you refer to the figures „Overview of the
Components" and „Assembly overview" when assembling.
Base Unit (Fig. a – c)
1. Screw the tubes (7) onto the stand (13). Use the four
screws (12), the metal plate (14), and the four nuts (15).
2. Attach the cover of the stand (16) to the stand tubes.
NOTE:
The nuts and screws (17) are pre-installed on the rear
of the switch housing.
3. Check if the screws (17) possibly have been screwed
into deeply. In this case, turn the screws back a little. Do
not screw them out all the way!
NOTE:
If a screw or a bolt should have dropped off, proceed
as follows:
54
PC-VL3111LB_IM
NOTE:
• Hold the pre-assembled unit (motor (18), switch
housing (6), and humidifier base (10)) so that the
motor points down.
• Insert one nut (M6) each into the shaft at the side
of the recesses for the tubes.
• Screw the two screws (17) on the rear of the switch
housing lightly into the nuts.
4. Set the pre-assembled unit for a depth of approximately
3 cm onto the stand tubes.
NOTE:
The humidifier cable must be routed between the two
tubes.
Secure the pre-assembled unit to the stand tubes by
tightening the two screws (17).
5. Fasten the base of the humidifier (10)
with the large screw (ST4*25 mm) to
the base of the stand. For this, insert
the screw from below through the
stand and its cover into the small outer
bore (Fig. on the right).
Fan (Fig. d)
6. Remove the pre-installed nut (20) from the motor (18).
Keep it close to hand.
7. Align the rear protection grid (19) with the motor
recesses (18).
NOTE:
The handle must point upwards.
8. Tighten the nut (20) for the rear protection grid clock-
wise.
9. Attach the propeller (3). When doing so, use the guide
pin on the motor shaft.
10. Tighten the screw (21) for the propeller anti-clockwise.
11. Remove the pre-fitted screw and nut (5) from the front
protection grid (22). Keep it close to hand.
12. Open the fastening hooks (2) at the front protection grid.
13. Attach the front protection grid by engaging the groove
of the hook (1) with the rear protection grid.
NOTE:
The holes for the screw (5) in the front and rear pro-
tection grid must be aligned.
14. Secure the protection grid with the screw and the nut (5).
15. Close the four fastening hooks (2).
Humidifier (Fig. e – f)
The tube already may have been installed on the switch
housing. In this case, continue the assembly from item 18.
16. Feed the tube (8) from front to back between the two
stand tubes (7). Then insert the tube from the bottom
upwards through the opening on the underside of the
switch housing (6).
07.12.22