HIKVISION VDP-H3211W Mode D'emploi

VDP-H3211W
Network Indoor Sta on UD20183B
ENGLISH
Diagram References
1 Appearance
1 Screen Screen 2 Microphone 3 Debugging Port 4 Network Interface
6 TF Card Slot 7 Alarm Terminal 8 Reserved
5 Loudspeaker
9 Power Terminal
Note:
The appearance of the device varies according to different models. Refers to the actual device for detailed
informa on.
The debugging port is used for debugging only.
2
Terminal and Wiring
There are 20 pins in the terminal on the rear panel of the indoor sta on: 2 RS-485 pins, 5
reserved pins, 4 relay output pins, 8 alarm input pins, and 1 GND pin.
Note: There are 20 pins in the terminal on the rear panel of the DS-KH6320-TE1: 11 reserved pins, 8 alarm
input pins, and 1 GND pin. Please refer to the specific model.
3
Installa on
It supports wall moun ng. There are two installa on modes.
Installa on Accessory Descrip on
The wall moun ng plate and junc on box are required to install the indoor sta on onto
the wall.
The dimension of junc on box should be 75 mm (width) × 75 mm (length) ×
(depth). The dimension of wall moun ng plate is shown.
Before You Start
Make sure the device in the package is in good condi on and all the assembly parts
are included.
The power supply the indoor sta on supports is 12 VDC. Please make sure your
power supply matches your indoor sta on.
Make sure all related equipments are power-off during the installa on.
Check the product specifica on for the installa on environment.
Wall Moun ng with junc on Box
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the junc on box to the hole chiseled on the wall.
3. Fix the wall moun ng plate to the junc on box with 2 screws.
4. Hook the indoor sta on to the wall moun ng plate ghtly by inser ng the plate
hooks into the slots on the rear panel of the indoor sta on, during which the lock catch
will be locked automa cally.
Wall Moun ng without junc on Box
1. Insert 2 expansion tubes into the wall.
2. Fix the wall moun ng plate to the junc on box with 2 screws.
3. Hook the indoor sta on to the wall moun ng plate ghtly by inser ng the plate
hooks into the slots on the rear panel of the indoor sta on, during which the lock catch
will be locked automa cally.
4
Ge ng Started
1 Ac vate Indoor Sta on
You are required to ac vate the device first by se ngs a strong password before you
can use the device.
1. Power on the device. It will enter the ac va on page automa cally.
2. Create a password and confirm it.
3. Tap OK to ac vate the indoor sta on.
2 Quick Configura on
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automa cally.
3. Configure the indoor sta on parameters.
- .Select Indoor Sta on and tap Next to link main door sta on.
a. Edit Floor and Room No.
b. Create and confirm SIP register password.
Note: If you want to add the indoor sta on to the door sta on, the SIP password of the indoor sta on
should be the same as the registra on password of the door sta on.
c. Tap Advanced Se ngs to edit Community No, Building No. and Unit No.
d. Op onal: Enable Indoor Sta on Se ngs and select the indoor sta on to link.
- . Select Indoor Extension and tap Next to link indoor sta on.
a. Edit No., Room Name.
b. Create and confirm SIP register password.
4. Linked related devices and tap Next. If the device and the indoor sta on are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the se ngs icon to pop up the Network Se ngs page.
b. Edit the network parameters of the door sta on manually or enable DHCP to get
the network parameters automa cally.
e. Tap OK to save the se ngs.
5. Tap Finish to save the se ngs.
Refers to Video Intercom Network Indoor Sta on Configura on Guide (Scan the QR code) for details.
Refers to Video Intercom Network Indoor Sta on Opera on Guide (Scan the QR code) for details.
1 1
50 mm
3
3
Lock Catch Lock Catch
Lock Catch Lock Catch
Rear Panel (without Interface)
3
1
2
7 8 9
6
122
Lock Catch
Lock Catch
Rear Panel (without Interface)
Unit:mm
Hook
Hook
Hook
Hook
Screw Wall Moun ng Plate
2
4
5
Lock Catch
Hook
Hook
Hook
Hook
Lock Catch
Screw Wall Moun ng Plate
Scan the QR code to get the
Configura on Guide for detailed
informa on.
Wall
Red RS-485+
RS-485
Red
RS-485-
Blue RES
Green RES
Yellow RES
Reserved
Yellow
RES
White RES
Black NO2
Red
COM2
Relay Output
Black NO1
Black COM1
Black AIN8
Black AIN7
White AIN6
White
AIN5
Alarm
White AIN4
Input
White AIN3
Device
AIN2
White
White AIN1
White GND
Junc on Box Wall
Scan the QR code to get the
Opera on Guide for detailed
informa on.