Publicité
Les langues disponibles
Les langues disponibles
GB
Inspecting the seals
Check the door seals around the oven regularly. If the seals are damaged,
please contact your nearest Service Centre (see Assistance). We recommend
that the oven is not used until the seals have been replaced.
Replacing the light bulb
Lamp
Holder
compartment
Lamp
Glass cover
! Do not touch the light bulb directly with your hands.
! Do not use the oven lamp as/for ambient lighting.
Sliding rack kit assembly
A
Left
Right guide
guide rail
rail
B
C
28
F
3. Grip the door on the two outer sides and
close it approximately half way. Pull the
door towards you, lifting it out of its slot (see
diagram). To replace the door, reverse this
sequence.
To replace the oven light bulb:
1. Remove the glass cover of the lamp-
holder.
2. Remove the light bulb and replace it
with a similar one: halogen lamp voltage
230 V, wattage 25 W, cap G 9.
3. Replace the glass cover (see
diagram).
To assemble the sliding racks:
1. Remove the two frames, lifting them
away from the spacers A (see figure).
2. Choose which shelf to use with the
sliding rack. Paying attention to the
direction in which the sliding rack is to
be extracted, position joint B and then
joint C on the frame.
D
! Do not place the sliding racks in position 5.
Automatic cleaning with the FAST CLEAN function
With the FAST CLEAN mode, the internal temperature of the oven reaches
500°C. The pyrolytic cycle is activated, burning away food and grime residues.
Dirt is literally incinerated.
Keep children away from the appliance during the automatic cleaning cycle
as surfaces may become very hot. Particles may ignite inside the oven as a
result of the combustion process. There is no cause for concern: this process
is both normal and hazard-free.
Before initiating the FAST CLEAN mode:
• clean the oven door;
• remove large or coarse food residues from the inside of the oven using a
damp sponge. Do not use detergents;
• remove all accessories and the sliding rack kit (where present);
• do not place tea towels or pot holders over the oven handle.
! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to
cool down.
! The programme may only be started once the oven door has been closed.
To activate the Fast Clean programme:
1. Switch the control panel on by pressing the
2. Press the
, the display will show the text "Piro", "nor" and the default
duration of 1:30 h (normal cycle) alternately.
3. Press button
, then turn the TIMER knob to adjust the default cleaning
level. There are 3 different levels to choose from, each with a pre-set duration
which cannot be modified:
1. Economy (ECO): turn the knob towards " ". Duration 1 hour.
2. Normal (NOR): initial level. Duration 1 hour and 30 minutes.
3. Intensive (INT): turn the knob towards " ". Duration 2 hours.
4. Press the
button to confirm.
5. Press the
button to begin the cleaning cycle.
An end time for the FAST CLEAN cycle (as for a normal cooking cycle) may
be programmed (see Programming the automatic cleaning end time).
! The desired Fast Clean mode will be confirmed and started automatically
if the CLOCK icon button is not pressed within 10 seconds from selecting
the cooking time.
Safety devices
• the door locks automatically as soon as the temperature reaches a high
value; the
icon lights up on the display;
• pressing the
button cancels the cleaning cycle t any time;
• if a malfunction occurs, the heating elements will be switched off;
• once the oven door has been locked, you cannot change the duration and
end time settings.
3.Secure the two frames with the guide
rails using the holes provided on the
oven walls (see diagram). The holes
for the left frame are situated at the top,
while the holes for the right frame are at
the bottom.
4. Finally, fit the frames on the spacers A.
button.
Publicité
