Sammic CK-301 Mode D'emploi page 7

On (7)
Starts the motor if the safety
devices are activated. If any of the safety devi-
ces is missing and you press "On" (7), the dis-
play shows "SE" (safety) to warn that a safety
device is missing.
Off (8)
Pressed once, the motor stops and the display
starts to flash to show that it is on standby. The
time and speed settings are still saved. After 3
minutes, or if the "off" button is pressed again,
the machine loses those settings and is reset.
Pulse (9)
While it remains pressed down, the motor switches
on if the safety devices are activated. When
released, the motor stops. If any of the safety
devices is missing and you press "Pulse" (9),
the display shows "SE" (safety) indicating that a
safety device is missing.
PLS. NOTE: Some vegetable preparation
machines have an emergency stop button.
This must be unlocked before starting the
machine.
Operation
When the CK-301 is connected the "Display" (1)
has two lines in the centre (standby). If you fit the
"Vegetable Cutter" attachment, "CA" appears on
the display. If you fit the "Cutter" attachment
"CU" appears for 3 seconds. This shows that the
control board has identified each attachment.
After these first seconds if CA attachment is
assembled in the display appear speed 1, and if the
"Cutter" attachment is assembled appear speed 5.
- Speed Control: The "Speed" pilot light (2) switches
on. There are 1 to 10 different speed settings in
"Cutter" mode and 1 to 5 speed settings in
"Vegetable Cutter" mode.
- Time Control: Only available in "Cutter" mode.
It is displayed when the "Time" pilot light (3)
switches on. There are two functions, continuous
mode and time-out:
- Continuous mode: A rotating line on the dis-
play means that this has been selected. If the
CK-301 is left on without any function being
selected, it switches off automatically after 30
minutes.
- Time-out: A time-out between 0 and 10 minu-
tes can be programmed. The time is selected
in ½ minutes. The "Display" (1) shows the
countdown in the same way. The last minute
counts down in seconds. When the programmed
time finishes, the machine stops and beeps.
- Energy saving: If the machine is stopped and
no button is pressed on the display for 5 minu-
tes, it switches off and only a dot is displayed.
Press any button to switch it on again.
START-UP
WARNING: Before using the machine for the
first time, clean the area in contact with food
with (lukewarm) soapy water, rinse and
leave to dry.
Handle the discs (A), vegetable cutter grids
(B) and the blades (T) very carefully because
they have very sharp edges.
To fit the attachments, unplug the CK from
the mains.
"Vegetable Cutter" operating mode:
· With the bayonet mechanism (Y) open (R), fit
the "Vegetable Cutter" attachment on the
motor block so that the three attachment lugs
are inserted in the quick-connect mechanism
holes. Close (Z) the bayonet mechanism (Y)
to lock the attachment on the motor block.
· In the CK-301/302 and CK-401 the hinged lid (J)
must be positioned as indicated in the illustra-
tions, being fixed with the pin (O).
· In the CK-301/302 the pusher plate (M) must
be positioned as indicated in the illustrations,
being fixed with the pin (N).
· In the CK-301/302 and CK-401/402, if the
header is to be used it must be positioned as
indicated in the illustrations, being fixed with
the pin (O).
Fitting discs (A) and grids (B).
- Release the lock (I), and open the hinged lid
(J).
- Fit the ejector (C) in its housing at the trailing
edge.
- The grid (B) is inserted in the top lid (D) pocket
at the right time during the process.
- Fit a disc (A) on the trailing axle. Insert the disc
(A) in the axle and rotate it clockwise until it
slots into place.
- In the case of the CK-401/402, screw the bit
(Q) or mixer (R) into the trailing axle depending
on the product being chopped.
- Lower the hinged lid (J) and apply the lock (I).
With the hinged lid (J) closed and the pusher plate
(M) down, if you press "On" (7) the motor starts.
With the motor stopped, the hinged lid (J) closed
and the pusher plate (M) up, if you press "On" (7)
the display start flashing indicating that the machine
is prepared to start, when the pusher plate is
lowered (M) the motor starts.
With the motor on, if you lift the pusher plate (M)
the motor stops. When you lower the pusher
plate (M), the motor re-starts automatically. If
the pusher plate (M) has not lowered in 30
seconds, the "On" button (7) must be pressed
again to start the machine.
With the motor on, if the hinged lid (J) is opened
the motor stops. When the hinged lid (J) is closed,
the "On" button (7) needs to be pressed again to
start the machine.
If the machine is left running with the pusher
plate (M) down, after 30 minutes the machine
stops automatically.
Operation with standard feed hopper (J) and
pusher plate (M). CK-301/302.
- The mallet (L) must be housed and locked. To
do so, rotate it anti-clockwise.
- Start the vegetable preparation machine.
- Lift the pusher plate (M). The motor stops.
- Add the products to the standard hopper (J).
- When you start to lower the pusher plate (M)
the motor starts and the cutting process
begins. Feed the product while gently lowering
the pusher plate (M). Repeat the process
several times.
- Press "Stop" (8) to finish.
WARNING: Applying too much force on the
pusher plate (M) could damage the product
and strain the motor.
Operation with standard feed hopper (K) and
pusher plate (M) in CK-401/402.
- The mallet (L) must be housed and locked. To
do so, rotate it anti-clockwise.
- Start the vegetable preparation machine.
- Lift the pusher plate (M) and rotate it anti-clock-
wise to clear the standard hopper (K) feed
chute. The pusher plate (M) can be left resting
on the pusher support (M). The motor stops.
- Add the products to the standard hopper (K).
- When the pusher plate (M) is rotated clockwise
the motor starts and the cutting process begins.
Feed the product while gently lowering the pusher
plate (M). Repeat the process several times.
- Press "Stop" (4) to finish.
ATTENTION: Excessive clamping force on
the lever (M) can damage the product and
force the motor excessively.
EN 7