Sammic CK-301 Mode D'emploi page 6

Each machine is identified as follows:
- Name and address of the manufacturer: SAMMIC
S.L - Basarte 1 Azkoitia. Gipuzkoa (SPAIN).
- The serial number is printed on the Guarantee
Card and in the Declaration of Conformity.
MODELS
This manual describes the installation, operation
and maintenance of the CK-301/302 and CK-
401/402. The model reference number and its
features are specified on the name plate attached
to the machine. This preparation machine has
been designed and manufactured in accordance
with the following European directives:
- Machinery Directive 2006/42/CE.
- Low Voltage Directive 2006/95/CE.
- Electromagnetic Compatibility Directive 2004/108/CE.
- Directives 89/109/EEC and 90/128/EEC on alu-
minium and plastic materials and articles in con-
tact with food.
- Aluminium alloys in contact with food standard
EN 601-2004.
- Hygiene and food contact materials standard:
ANSI-NSF 8 and ANSI-NSF 51.
- Vegetable Preparation Machines Standard: UNE-
EN 1678.
- Food processors and mixers standard: UNE-EN
12852.
- Protection level in accordance with UNE-EN
60529: Controls IP-55 and rest of machine IP-23.
- The 120V/60Hz/1~ models comply with the UL-
763 and CSA C22.2 standards.
IMPORTANT INFORMATION
- This machine is not designed for
use by people (including children)
with reduced physical, sensory or
mental capabilities or lacking the
necessary experience or knowled-
ge, unless they have received
supervision or instructions from a
health and safety expert.
- This machine is for supervised
use. Never leave the machine run-
ning unsupervised.
- Before using the machine for the
first time, clean the area in contact
with food with (lukewarm) soapy
water, rinse and leave to dry.
- The blade set (T)
cutter/emulsifier has very sharp
6 EN
blades, so they must be handled
with care.
- Before undertaking any cleaning,
inspection or repair work on the
machine, the machine must be
unplugged from the mains.
INSTALLATION
For optimum service and maintenance, please
follow these instructions.
INSTALLATION SITE
You are advised to install the CK-301/302 on a
steady surface -this must not act as a soundbo-
ard- elevated at a height of 700-900 mm, and 600-
800 mm for CK-401/402. Place the collector
underneath the food outlet. The machine is not
fixed in place and can be moved around easily.
ELECTRICAL CONNECTION
Check that the CK electrical characteristics match
the grid power supply.
The CK is supplied for 230V 50-60 Hz single phase
power or 120V 50-60 Hz single phase power.
Prepare a wall-mounted socket, with a general dis-
connecting switch and with a residual current and
magneto thermal protection of 2P (of 13A to 20A) with
its corresponding socket. Fit a general switch or the
plug in an accessible place to disconnect the machine.
WARNING: THE EARTH CONNECTION IS OBLI-
GATORY. DANGER OF ELECTROCUTION. The
converter includes a filter that shunts power dis-
turbances to safety ground. The residual
current device may therefore cause untimely
tripping. You are advised to use a suitable resi-
dual current device for the machine or a super
immunised RCD. Moreover, the machine inclu-
des an external screw for its connection to a
ground equipotential system.
The motor is three-phase in every model and
controlled by a variable frequency drive.
Do not change the variable frequency drive settings
under any circumstances.
Direction of rotation: Because the motor is three-
phase, the direction of rotation may be incorrect.
The CK motor rotates anti-clockwise. To reverse
of the
it, switch two motor wires at the variable fre-
quency drive outlet.
Power cable characteristics
The CK is supplied with a 1.5 m thermoplastic-
sheathed power cable.
ELECTRONIC CONTROL FUNCTIONS AND
OPERATION
Display (1)
Shows speed, operating time and warnings.
"Speed" pilot light (2)
When it is on, the "display" shows the speed.
"Time" pilot light (3)
When it is on, the "display" shows the time.
Function (4)
This button switches between
the "speed" and "time" functions. The selected
function appears on the display and the pilot
light comes on.
This button only works in "Cutter" mode. In
"Vegetable Cutter" mode this button does not
work because only the "speed" function is acti-
vated.
Up (5)
Each time the key is pressed the setting on the
display increases.
Down (6)
Each time the key is pressed the setting on the
display decreases.