Télécharger Imprimer la page

Chamberlain LiftMaster PROFESSIONAL SECURITY+ 1265LMC Manuel Du Propriétaire page 28

Publicité

Les langues disponibles

Les langues disponibles

Using the Wall-Mounted
Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push bar to open or close
the door. Press again to reverse the
door during the closing cycle or to
stop the door while it's opening.
Light feature
Press the Light button to turn the
opener light on or off. It will not control the opener
lights when the door is in motion. If you turn it on and
then activate the opener, the light will remain on for 4-
1/2 minutes. Press again to turn it off sooner. The 4-
1/2 minute interval can be changed to 1-1/2, 2-1/2, or
3-1/2 minutes as follows: Press and hold the Lock
button until the light blinks (about 10 seconds). A
single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat
again for a 3-1/2 minute interval, etc., up to a
maximum of four blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-
held remote controls. However, the door will open and
close from the Door Control, the Outside Keylock and
the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The
Lock feature will also turn off whenever the "Smart"
(learn) button on the motor unit panel is activated.
Additional features when used with the
3-Channel hand-held remote
A) To control the opener lights:
In addition to operating the door, you
may program the remote to operate the lights.
1. With the door closed, press and hold a small
remote button that you want to control the light.
2. Press and hold the Light button on the Multi-
Function door control.
3. While holding the Light button, press and hold the
Lock button on the door control.
4. After the opener lights flash, release all buttons.
B) To operate one door using all three
buttons on the hand-held remote:
You may program the remote to
open the door with the large button,
stop the door's movement with the
Push
middle button, and close the door
Bar
with the third button.
Lock
NOTE: If remote is already programmed, you must
Button
first erase all codes. See Programming.
Light
Button
1. With the door closed, press and hold the large
remote push button.
2. Press and hold the Lock button on the door
control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
To Open the Door Manually
• To prevent possible SERIOUS INJURY or DEATH from
a falling garage door:
– If possible, use emergency release handle to
disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.
– NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope
knot becomes untied, you could fall.
The door should be fully
closed if possible. Pull down
on the emergency release
handle and lift the door
manually. To reconnect the
door to the opener, press the
door control push bar.
The lockout feature prevents
the trolley from reconnecting
automatically, Pull the
emergency release handle
down and back (toward the
opener). The door can then be
raised and lowered manually
as often as necessary. To
disengage the lockout feature,
pull the handle straight down.
The trolley will reconnect on the
next UP or DOWN operation.
28
WARNING
CAUTION
Emergency
Release
Handle
(Pull Down)
MANUAL DISCONNECT
POSITION
Emergency
Release Handle
(Pull Down & Back
Towards Opener)
LOCKOUT POSITION
Open
Stop
Close
Trolley
Release
Arm
Trolley
Release
Arm

Publicité

loading