Makita 9561CR Manuel D'instructions page 5

ENGLISH (Original instructions)
1. Shaft lock
2. Slide switch
3. Indication lamp (speed adjusting
dial)
4. Indication lamp
5. Speed adjusting dial
6. Wheel guard
7. Bearing box
8. Screw
9. Lever
10. Lock nut
SPECIFICATIONS
Depressed center
wheel diameter
Spindle thread
Rated speed (n) / No load speed (
Overall length
Net weight
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
All manuals and user guides at all-guides.com
Explanation of general view
11. Depressed center grinding wheel/
Multi-disc
12. Inner flange or super flange
13. Lock nut wrench
14. Marking A
15. Marking B
16. Marking C
17. Pin
18. Vent
19. Abrasive cut-off wheel/diamond
wheel
115 mm 9561CR
125 mm 9562CR
M14
n
) 12,000 min -1
0
289 mm
2.2 kg
ENE048-1
ENF002-2
GEA010-1
GEB033-5
20. Inner flange
21. Wheel guard for abrasive cut-off
wheel/diamond wheel
22. Abrasive cut-off wheel
23. Diamond wheel
24. Thickness: Less than 4 mm
(5/32")
25. Thickness: 4 mm (5/32") or more
26. Exhaust vent
27. Inhalation vent
9564CR 9561CVR
9565CR 9562CVR
M14 M14
2,800 -
12,000 min -1
12,000 min
299 mm 289 mm
2.2 kg 2.2 kg
/II
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
9564CVR
9565CVR
M14
2,800 -
-1 -1
12,000 min
299 mm
2.2 kg
5