Publicité
Les langues disponibles
Les langues disponibles
Using the remote control
CR-314 Remote Control
Note that greyed-out buttons on the remote control are DVD-
specific and are not used with the CD player.
Ensure that CD mode is selected using the
toggle button. The 'CD' LED above the
button is lit briefly when CD mode is selected.
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
This button enables you to repeat any section of music within
a track. Whilst the disc is playing, press the
start of the section you wish to repeat. 'REPEAT' is shown on
the display and the letter 'A–' flashes. Press the button a second
time when you reach the end of the section you wish to repeat.
The 'A–B' letters stop flashing and remain lit. This section will
repeat until you press
or
or
. The forward search button
(
) moves forward within the selected loop.
To repeat the entire CD or a pre-programmed selection of tracks
press
once: 'REPEAT' lights on the display. To repeat a
RPT
particular track, select that track and then press
that 'REPEAT 1' is shown on the display.
different track, that track is repeated instead.
To cancel the repeat function press
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
Opens and closes the CD tray
Pause, Play and Stop (see page 5)
Press once to shuffle play CD tracks (i.e. play them in
a random order). Press again to cancel shuffle play.
Press
TITLE
once to display the remaining time of the currently
playing track. Press again to display the time remaining of the
disc. Press a third time to turn the text display on.
Press
again and the display reverts to its original setting,
TITLE
showing the time elapsed for the current track.
For CDs with text, pressing
once while the disc is loaded
TITLE
but not playing displays the artist's name.
Pressing
TITLE
a second time displays the total number of
tracks and the total playing time.
CD72/82
6
All manuals and user guides at all-guides.com
CD/DVD
CD/DVD
CD/DVD
DISP (display)
CD
A–B
CD
DVD
A–B
button at the
DISP
A-B
RPT
RPT (repeat)
RPT
twice so
If you now select a
a third time.
RPT
Search and Skip Track
OPEN
Playback control
P MODE
MODE
ZOOM
TITLE
ANGLE
0–9 keypad
This allows direct access to individual tracks on the disc. To
select a track, press the corresponding keypad button and then
press
For example, to play track 15, press and hold
on the display moves to the left, then press
CLEAR
CD/DVD REMOTE
If you make a mistake whilst programming you can delete
DVD
the last entered track by pressing
programmed tracks, press
1
2
3
displayed.
To exit the program facility, press
4
5
6
7
8
9
PROG (Program)
0
CLEAR
PROG
You can program a selection of up to 24 tracks from a disc to
play in any order. Select a track by using the
then press
appears on the display to indicate that you have started
programming a sequence). Repeat these steps to program the
remaining tracks in your selection. Alternatively, press
once and enter your track selection using the 0–9 keypad.
OK
OPEN
The display shows the track numbers programmed, the total
length of the programmed sequence and the number of tracks
programmed (shown by a number below the word 'STEP').
Each time you enter a track the number below 'STEP' increments
by one and flashes until you press
press
PROG
and you will have to reselect the track.
Press
MUTE
sequence from the start. Press and hold
programmed sequence. Press
facility: the display flashes 'CONTINUE' and shows '0'.
MUTE
Stops sound to the speaker outputs of certain Arcam amplifiers.
P
SUBT
TITLE
MENU
Volume +/–
Adjusts the volume on Arcam remote-controllable amplifiers.
AUDIO
MEM
RTN
Note that the volume (+/–) controls and
no effect on the audio output level of the CD players.
SETUP
STATUS
SRCH
NOTE: Remember to install the two AAA batteries supplied
CR-314
before trying to use your remote control.
Do not place anything in front of the display area on the
CD player (where the IR receiver is located), or the remote
control may not work.
. For tracks greater than 9, enter the digits in sequence.
5
.
. To delete all the
CLEAR
repeatedly until '0' is
CLEAR
.
PROG
PROG
to program the track into memory ('PROGRAM'
PROG
to confirm. If you fail to
within about five seconds the display stops flashing
to play the program. Press
again to replay the entire
CLEAR
again to exit the program
PROG
MUTE
until the number
1
and
buttons,
PROG
to erase the
button have
Publicité
