Publicité
Les langues disponibles
Les langues disponibles
ASSEMBLY OF STAND
1.
Align the holes in the supporting legs with each other
and screw the legs together with 2 screws M8 x 40, 2 flat
washers Ø8 and 2 lock nuts M8.
2.
Fit the cross stays with screws M8 x 25 and nuts M8. Do not
overtighten so that the cross stay cannot move.
FIG.
3
ASSEMBLY OF SPRING GUIDES
Fit the spring guide, undo the screw, washer and nut on the
spring guide, put the spring and washer on the spring guide,
press the support leg against the blade and insert the spring
guide in the hole in the support leg and lock in place.
FIG.
4
ASSEMBLY OF MOTOR UNIT
Fit the motor unit on the stand with the washers and nuts.
FIG.
5
ASSEMBLY OF FIXED AND ADJUSTABLE BLADE
GUARD
1.
Fit the outer blade guard on the support leg (B) and the
bracket for the guard with countersunk crosshead screw
M6 x 15, screw M8 x 40, screw M8 x 15, lock nut M6,
lock nut M8.
FIG.
6
2.
Fit the inner part of the inner blade guard on the log cradle.
FIG.
7
3.
Fit the adjustable guard (A).
FIG.
8
4.
Fit the bottom casing (B) on the log cradle with M6 x 12
screw and lock with M6 x 25 screw.
FIG.
9
FITTING THE SAW BLADE
1.
Fit the inner flange, blade and the outer flange and the M20
nut on the motor shaft.
FIG.
10
FIG.
11
2.
Hold the outer flange with one spanner and tighten with the
other spanner.
FIG.
12
FITTING THE OUTER BLADE GUARD
1.
Fit the outer part of the inner blade guard on the log cradle
with 2 screws (M6 x 12) and then fit the outer and inner part
of the inner blade guard together with M5 x 6 screws.
FIG.
13
FIG.
14
2.
Remove the bottom plastic casing (C) on the inner blade
guard.
FIG.
15
3.
Fit the outer guard and tighten the screws.
FIG.
16
4.
Now replace the bottom plastic casing.
FIG.
17
FITTING THE COVER PLATE AND EXTENSION
1.
Fit the log cradle extension (D) with 2 screws M8 x 12, 2
washers Ø8 and 2 lock nuts M8.
FIG.
18
2.
Fit the cover plate on the log cradle with 3 screws M8 x 15
and 3 lock nuts M8. Now fit the cover plate on the inner
blade guard with 2 screws M5 x 8 and 2 lock nuts M5.
FIG.
19
FITTING THE COVER FOR THE LOG CRADLE
1.
Fit handle.
FIG.
20
2.
Undo the 2 screws M4 x 6 on the cover for the log cradle.
FIG.
21
3.
Fasten the cover on the cover plate for the log cradle and
tighten the 2 screws M4 x 6.
FIG.
22
FIG.
23
FITTING THE EXTENSION ARM, SUPPORT AND
HANDLE
FIG.
24
FIG.
25
FIG.
26
FITTING THE LOCK KNOBS
Fit 2 lock knobs with the screws M8 x 20.
FIG.
27
FITTING THE EMERGENCY STOP
Fit the emergency stop on the motor plate with 4 screws M4 x 55.
FIG.
28
USE
NOTE:
Before using the product it must be secured to the surface
through the four holes in the feet.
FIG.
29
TO CHECK BEFORE USE
Check the following points before use.
–
Check that the blade is intact, sharp and does not catch
on any parts.
EN
33
Publicité
