Energy Power Bar Manuel Du Propriétaire page 5

CONNECTION
1. Connecting the soundbar to your TV: The soundbar part of your Energy Power Bar
system is what needs to be connected to your TV, Cable Box or Satellite Receiver. If
you have other devices connected to your TV, such as a DVD /BluRay player, gaming
system, etc., connect the soundbar to the TV so that you can listen to all those and
your TV through the soundbar. If there are no other devices connected to your TV
other than a cable or satellite box and you receive all of your television programs
from that box, you can connect the soundbar to either that box or your TV. There are
three different ways to connect the soundbar to your TV, Satellite or Cable box. Since
most High Definition TV's, Satellite and Cable boxes have an DIGITAL OPTICAL AUDIO
OUTPUT, we have included that cable. Simply connect one end of that included
cable into the corresponding output of your TV, Satellite or Cable box and connect
the other end of the cable into the DIGITAL OPTICAL INPUT on the back panel of the
soundbar. If you do not have an optical digital output, you can use analog left and
right audio outputs on your device and connect them to the analog left and right
inputs on the soundbar (cable NOT supplied). A third choice would be to connect
from a headphone output on your device to the analog left and right inputs on the
soundbar (cable NOT supplied). Once you have made a connection, connect the
supplied soundbar power supply into the "DC Input" on the back of the soundbar
and turn the Main Power Switch on the back of the soundbar on.
TV Connection Panel
TV Connection Panel
Power Supply
and AC Cord
All manuals and user guides at all-guides.com
OFF ON
Soundbar Connection Panel
Digital Optical Cable
(Supplied)
3.5mm to Male RCA
Cable
(Not Supplied)
Male RCA to Male
RCA Cable
(Not Supplied)
Soundbar Connection Panel
Soundbar Connection Panel
2. Connecting the subwoofer to the soundbar: Once you have placed the subwoofer
in the room, take the supplied subwoofer power cord, plug one end into the sub-
woofer where it is labeled "AC In" and plug the other end into an active electri-
cal socket. Turn the Main Power Switch on the back of the subwoofer on. On the
soundbar, make sure the status light is either solid green or orange (press SOURCE
button once if light is steady red). The subwoofer status lights will flash blue as
it looks for the wireless soundbar signal. Once the signal is found, the subwoofer
is "paired" with the soundbar, meaning it is wirelessly connected to it and the
subwoofer status light will stay solid blue.
Subwoofer Rear Connection Panel
PROGRAMMING YOUR TV REMOTE TO OPERATE THE SOUNDBAR
The Energy Power Bar has been pre-programmed to work with many Samsung TV's,
so if you have one check to see if your Samsung TV remote automatically changes
the soundbar volume and puts the soundbar into "STANDBY" when MUTE is pressed.
If so, you do not need to manually program your TV remote. Also, if once you have
connected your Energy Power Bar system you find that your TV remote automati-
cally controls the volume up and down through the soundbar (indicating you have
a "variable" audio output on your TV) you will not need to program VOLUME UP (+)
or VOLUME DOWN (-) when programming your TV remote. Program your TV remote
control (or satellite or cable box remote control if your soundbar is connected to
that) according to the separate programming instructions included with the sound-
bar. As an example, perform the following steps to program the soundbar to adjust
its volume up (+) when you press the volume up (+) button on your TV remote:
Soundbar Front
Control Panel
1. IF THE SOUNDBAR IS IN STANDBY MODE (solid red status light), push any button
on the soundbar until status light is solid orange OR green. With the status light
showing either solid orange or solid green, press and hold down both the SOURCE
and MUTE button on the front of the soundbar at the same time (approximately 3
seconds) until the status light flashes orange.
2. Press and hold down VOLUME UP (+) button on soundbar until status light stays
solid orange.
3. Hold your remote within one foot of the front of the soundbar. Press the VOLUME
UP (+) button on your remote control four times. The first three presses the status
indicator light will flash orange each press, and then will turn solid green on the
fourth press. This indicates that the soundbar has "learned" the VOLUME UP (+)
function on your remote.
Status Light
AC Power Cord
STATUS LIGHT
SOURCE
MUTE
VOLUME UP
VOLUME DOWN