Braun BC15 Mode D'emploi page 2

English
Battery precautions
1. Do not use rechargeable batteries.
2. Use only alkaline AA batteries of the same or equivalent type.
3. Insert batteries with the correct polarity.
4. Keep batteries away from children.
5. Dispose of exhausted batteries according to local legal
requirements. Do not dispose them by throwing away with normal
household rubbish.
6. Avoid short circuiting the contacts in the battery compartment
and battery terminals.
7. Remove batteries from the unit if it will not be used for long
period of time.
8. Exhausted batteries should be removed from the battery
compartment to prevent over-discharge, which can cause
leakage and may cause damage to the clock.
Getting started
Option A: Battery operated
1. Remove the battery door.
2. Insert 3xAA size new batteries as indicated in the battery
compartment, and press the "reset" key to reset the clock. The
display will turn on after a few seconds.
3. Close the battery door.
Option B: Adaptor operated
1. Plug the adaptor into the DC jack at the back of the clock, and
press the 'reset' key to reset the clock. The display will turn on
after a few seconds.
Function keys
TIME SETTING / NEUTRAL / ALARM SETTING switch
- Slide the switch to the TIME SETTING position to set the clock
time.
- Slide the switch to the ALARM SETTING position to set the alarm
time.
- Slide the switch to the NEUTRAL position to exit the setting
mode and return to normal display.
+ Key
- When the setting switch is in the NEUTRAL position, press the +
key to change between 12 and 24 hour display format.
- In TIME SETTING or ALARM SETTING mode press to increase the
setting value. Press and hold to speed up the setting.
- Key
- In TIME SETTING or ALARM SETTING mode press to decrease
the setting value. Press and hold to speed up the setting.
ALARM ON / OFF slider
- Shift the ALARM ON / OFF slider up to enable the alarm.
- Shift the ALARM ON / OFF slider down to disable the alarm.
SNOOZE / LIGHT touch button
- Tap to turn on the backlight for 10 seconds.
- Tap to stop the alarm and activate the 5 minute snooze function.
RESET key
- Press by using a pin to reset all values to default. In case of a
malfunction, the unit has to be reset.
PROJECTION key
- Press to rotate the projection image by 90 degrees increments.
BRIGHTNESS key
- Press to choose between 4 different backlight settings: NO
BACKLIGHT, WEAK BACKLIGHT, MEDIUM BACKLIGHT and
STRONG BACKLIGHT.
Product description (Image 1)
1. LCD display
2. Projection arm
3. Time set
4. Alarm set
5. ALARM ON/OFF slider
6. Projection key (ON/OFF and rotate)
7. + key
8. - Key
9. RESET key
10. DC Jack
11. Battery compartment
12: Brightness key
13. SNOOZE / LIGHT touch-bar
14. Projector
Display symbols (Image 2)
A. Time
B. Low battery indicator
C. Alarm icon
D. Alarm time
Setting the time
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the TIME SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Setting the alarm
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the ALARM SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Using the alarm and snooze function
1. Enable the alarm by shifting the ALARM ON / OFF slider up (so
the green detail is visible). The bell icon will appear on the LCD
display.
2. Tap the SNOOZE / LIGHT touch button to stop the alarm and
activate the snooze function. When the snooze function is
activated, the bell icon will flash.
3. To disable the alarm and snooze function, shift the ALARM ON /
OFF slider down. The bell icon will disappear.
Note: When the snooze function is activated, the alarm will
automatically start again after 5 minutes. The snooze function will
not stop unless the ALARM ON / OFF SLIDER is shifted down.
Battery replacement
When the LCD display becomes dim or the battery icon flashes,
replace with 3 new AA size batteries at once.
Choosing the backlight brightness
Press the 'display brightness' button to choose between the
four backlight brightness options. If the DC adaptor is used, the
backlight can remain on permanently. If no DC adaptor is used the
backlight will automatically turn off after 10 seconds.
Using the projection function
1. When the batteries are used to power the clock, the projection
will be ON for 10 seconds after press 'SNOOZE / LIGHT' touch-bar.
2. When the DC adaptor is used to power the clock, the
continuous projection feature can be enabled. Press and hold
the Projection button for 3 seconds to disable the continuous
projection feature. It can be enabled by pressing the Projection
button again.
3. The projection arm can be tilted 180 degrees for user
customisation of the projection image on a dark wall or ceiling
within 1-4 metres.
4. The projection can be rotated in 90 degree increments by
pressing the 'projection' button.
Note: The projection function may not work correctly at distances
of less than 1 metre.