Hikmicro G Serie Guide De Démarrage Rapide page 5

1. Appearance (Page 1 – A)
No. Component
Interface
1
Cover
2 Microphone
Charging
3
Indicator
4 Loudspeaker
Touch
5
Screen
Power
6
Button
Shutter
7
Button
8 File
9 Back Button
10
Navigation
Button
11 Laser Button
12 Battery
Laser
13 Distance
Meter
14 Optical Lens
15 LED Light
16 Thermal Lens View the thermal image.
17 Focus Ring
Tripod
18
Interface
Hand Strap
19 Buckle
Interface
20 Focus Trigger
English
Function
Protect the interfaces from dust.
Input audio information.

Red: Charging

Green: Fully charged
Play voice note, voice alarm, and
video voice.
Touch the screen to set
parameters.
Hold: Power on/off
Press: Perform image correction
with a shutter click in the
camera.

Inspection Route Mode:
Press the button to view the
information of inspection
points.

Non-Inspection Route
Mode: Press the button to
view the capture and video.
Exit the menu or return to
previous menu.
Menu Mode:
 Press , , , and  to
select parameters.

Press OK to confirm.
 Press  to enter the
submenu.
 Press  to return to the
previous menu.
Non-Menu Mode:
Press  to turn on/off the

LED light supplement.
Press  to start digital

zoom.
Hold the button to turn on laser,
and release the button to turn
off laser.
Provide power for the device.
Measure the distance with laser.
View the optical image.
Increase ambient brightness in
dark environment.
Adjust the lens position at the
optical axis of the thermal lens.
Install the tripod.
Insert the screw to fix the hand
strap buckle.
Pull the trigger to enable laser
assisted focus/auto focus
function.
No. Component
21 Main Trigger
Hand Strap
22
Hole
Memory
23
Card Slot
Type-C
24
Interface
CVBS
25
Interface
Reserved
26
Card Slot
Micro HDMI
27
Interface
Note:

The warning sign is under the laser and on the left of
the device.

The interfaces may vary according to different
models. Please refer to the actual products.

Initialize the memory card before first use of it.

Please refer to the product specification for details
about the device accessories.
2. Charge Device via Charging Base
(Page 1 – B)
After the device starts up, the OSD (on-screen display)
shows the battery status. When the battery is low, charge
the device and ensure it works properly.
For the first charge, charge the device for 10 hours when
the device is turned on.
Note：

The built-in cell battery that powers the real time
clock (RTC) of the device may drain during longtime
transportation or storage. It is recommended to
recharge the RTC battery for the wellfunctioning of
the device clock.
 To fully charge the RTC battery, the following
requirements should be met:
a) The rechargeable lithium batteries should be
installed on the device.
b) The device should keep working for more than
10 hours before shutting down.
Steps:
1. Hold the device, and press both battery lock catches
of the device.
2. Hold the lock catches, and draw the battery base to
take out the battery.
3. Insert the battery into the charging base. You can see
the charging status via the pilot lamp on the charging
base.
4. When the battery is fully charged, draw the battery
from the charging base.
5. Insert battery into the device.
Note: Please purchase the charging base in advance.
3. Mount Interchangeable Lens
(Optional)(Page 2 – C)
Note: Please purchase the interchangeable lens in
advance.
3
Function

Pull the trigger to capture or
scan the QR code.

Hold the trigger to record
videos.
Thread the lower part of the
hand strap through the hole.
Insert the memory card.
Connect to power supply and
transmit data.
Connect the device and display
unit to view the image for
details.
Insert the reserved card.
Connect the device and display
unit with Micro HDMI (type D) to
HDMI (type A) cable to view the
image for details.