Publicité
Les langues disponibles
Les langues disponibles
N40-5
5.2. Push the release lever of the left side mechanism completely upwards moving it
over the side trim (Fig. 8) and pull the visor away from the helmet (Fig. 9).
5.3. Release the release lever and replace it downwards in its original position moving
it over side trim.
5.4. Follow the same steps on the right side of the helmet.
6.
VISOR ASSEMBLY
6.1. Place the left side of the visor on the corresponding side mechanism centring the
side hole of the visor on the mechanism itself (Fig. 9).
6.2. Push the release lever of the mechanism completely upwards moving it over the
side trim and press the visor against the side mechanism (Fig. 8, 9).
6.3. Disengage the release lever and replace it downwards in its original position mov-
ing it over the side trim. Then check that the visor remains attached to the mech-
anism by pulling it outwards.
6.4. Follow the same steps on the right side of the helmet.
6.5. If desired, replace the peak above the visor, and finally always replace both lateral
latches (see instructions above).
6.6. Close the visor completely.
WARNING
-
Make sure that the mechanisms are working properly. Open and close the visor
making sure that the mechanisms hold it in the different positions.
If necessary, repeat the above-mentioned steps.
-
If the peak is assembled over the visor check the proper functioning as described
previously.
-
Do not use the helmet if the visor and the lateral latches have not been assembled
properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a
Nolangroup authorized dealer.
SIDE PLATES
When the helmet N40
is configured without the visor the side plates must be assem-
5
bled in its place.
7.
SIDE PLATES ASSEMBLY
To assemble the side plates first remove the lateral latches and (if assembled) the peak
and the visor (see instructions above).
7.1. Place the left side plate on the corresponding side mechanism centring its hole on
the mechanism and its teeth (Fig. 10).
7.2. If you wish to assemble the peak above the plates see the relevant installation
instructions.
7.3. Assemble the left lateral latch as indicated in the instructions above.
7.4. Follow the same steps on the right side of the helmet.
16
INSTRUCTIONS FOR USE
8.
SIDE PLATES DISASSEMBLY
To disassemble the side plates first remove the lateral latches and (if assembled) the
peak (see instructions above).
Then remove the plates from the side mechanisms.
Next, reassemble the visor and then the peak (if any) as explained in the previous
instructions.
WARNING
-
When using the helmet in a configuration without the visor, always assemble the
lateral latches and the side plates.
-
Do not use the helmet if the plates and the lateral latches have not been assem-
bled properly.
-
If the peak is assembled over the plates the proper operation as described previ-
ously.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a
Nolangroup authorized dealer.
VISION PROTECTION SYSTEM ( VPS ) ( VPS - 11S )
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™(*) polycarbonate
moulded sunscreen with scratch-resistant/fog-resistant treatment. Very simple and prac-
tical to use. Just lower to activate it or lift to remove it from the field of vision. It is useful
in all sorts of situations, both on long journeys out of town and shorter town trips.
Moreover, the innovative fastening system allows you to assemble and disassemble
the sunscreen without the need for any tools for ordinary maintenance and cleaning
operations.
VPS OPERATION
The VPS mechanism allows to activate the sunscreen by simply lowering it until it par-
tially covers the visor field of vision. In this way, the desired light transmittance reduc-
tion is achieved. At any time, without operating the visor, the VPS can be deactivated
with a simple movement and easily lifted up to restore the normal conditions of visibility
and protection guaranteed by the approved helmet visor.
To deactivate the VPS, push the side slider completely downwards (Fig. 11A).
To completely activate the VPS push the side slider completely upwards (Fig. 11B).
The VPS is adjustable in a range of intermediate positions to ensure the best comfort
for the user with respect to the terms of use.
PRECAUTIONS FOR USE
Current homologation standards (ECE22-06) establish that the minimum light trans-
mittance levels of visors must be no less than 80%; for homologated sunscreens, the
minimum transmittance level must be no less than 20%.
The regulation itself also contemplates the simultaneous use of the visor and sun-
screen, both as standard.
(*)
LEXAN is a trademark of SABIC.
N40-5
17
INSTRUCTIONS FOR USE
Publicité
