Samsung SMT-190D Serie Mode D'emploi page 24

USER'S MANUAL
On the contrary, in 8 Channel mode, the data
recorded in Channel 1 mode will not playback and
only the data recorded in 8 Channel can be played.
If you want to switch from 1 channel mode back to 8
channel mode, set 1CH RECORD SUPPORT to OFF
and exit the MENU. Then, you will see a message,
"SYSTEM CHANGE 8CH DVR?" asking if you want to
switch the system mode. If you click OK, the system
will be switched.
[ON/OFF]
8. LANGUAGE
Many language are provided and select a your
language. English is the default.
[ENGLISH/FRANÇAIS/DEUTSCH/ESPAÑOL/
ITALIANO/PYCCKИЙ/SVENSKA/PORTUGUÊS/
/POLSKI/ČESKY/
DANSK/HRVATSKI]
5-9) NETWORK SETUP
This section of the manual is intended for users who will
install this security system in a network environment.
If you have difficulty setting the network,we recommend
contacting your network administrator.
• Static
• DHCP
• PPPoE(ex. ADSL)
• Function: Allow users to select the STATIC
(fixed) IP, DHCP, PPPoE of Setting.
• Setting method: Move to, NETWORK SETUP
MENU by using /KEY in the SETUP
MENU, then press the ENTER SWITCH to
display the OSD as shown in the figure below.
(The figure shows the initial setting status)
NETWORK SETTING
1. NETWORK ACCESS
. HTTP PORT
. PICTURE QUALITY
NETWORK STATUS
IP ADDR
GATEWAY
SUBNETMASK
DNS 1
DNS 
MAC ADDR
DDNS ADDR wff0000.websamsung.net
MOVE TO EACH item by using / KEY, and using
/ KEY to change the set value.
Static IP User
- Constituted by Static IP on the TCP/IP network
1) Move to 'STATIC...' by using / KEY at NETWORK
ACCESS, then press ENTER SWITCH to set
All manuals and user guides at all-guides.com
/TÜRKÇE/DUTCH/
07/07/07 00:00:01
STATIC...
00080
NORMAL
19.168.1.
19.168.1.65
55.55.55.0
168.16.6.1
168.16.6.
00:0:6f:ff:00:00
STATIC...
(STATIC : Select in case the network configuration of
monitor is fixed IP (Public or Private IP)
IP ADDR
GATEWAY
SUBNETMASK
DNS 1
DNS 
) Move to IP ADDR / GATEWAY / SUBNETMASK by
using / KEY .
) Press ENTER SWITCH and type in IP ADDR /
GATEWAY / SUBNETMASK respectively.
) DNS 1 and DNS  will be automatically set to DNS as
shown above. Use / KEY to change it.
DHCP User
- Constituted by Dynamic IP on the cable/xDSL
modem network
You can use the SMT-190DN products through the
network using Dynamic IP on cable/xDSL modem.
In this case, it should be connected with DDNS to
support the Dynamic IP. In case of a configuration using
DHCP, as the connection to SMT-190DN is made using
domain names (EX : http://wff0000.websamsung.net) that
are automatically registered in our DDNS server,
IP address, Subnet Mask and Gateway that are in the
network tab of Admin Mode are not to be changed.
The proper domain names of SMT-190DN are
automatically registered to DDNS server installed in
our company in case of modem connection.
The default IP type is DHCP .
1) Connect as the figure below and turn on the power of
the equipment in the order shown.

) After setting, move to the main screen by using the
MENU button.
) Set values will be stored shown below. It takes 0 to
5 seconds.
Eng-
07/07/07 00:00:01
STATIC ACCESS
19.168.1.
19.168.1.65
55.55.55.0
168.16.6.1
168.16.6.
 