ETI BCB-22-LB4-8-CP3-MV-LVD Guide D'utilisation Et D'entretien

Order # 64701301
64706201
64702301
Use and Care GUide
TrOffer series insTallaTiOn GUide
120-277V 50/60Hz 15W/19W/24W/29W 24W/29W/32W/39W
Package contents
Description Quantity
Fixture 1
Default setting is at highest wattage, 3500k cct
nOTe: Keep your receipt and these instructions for proof of purchase. All wiring should be performed by a qualified electrician. Disconnect power before installing or servicing. This
fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances. Do NOT use this product for other than intended use. To prevent
early product failure, luminaire should only be used in operating environments ranging from -20°C (-4°F) to 40°C (104°F). All wiring is recommended to be capped with UL approved
wire connectors. Wear gloves and safety goggles always when removing luminaire from carton, installing, servicing or performing maintenance. Avoid direct eye exposure to the light
source while it is on. Account for small parts and dispose packing material as these may be hazardous to children.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes. Make certain power is OFF before installing or maintaining
fixture. No user serviceable parts inside. Turn off electrical power at fuse or circuit breaker box before wiring the luminaire to the power supply. Verify that the voltage is correct by comparing
it with the luminaire label information. Keep combustible and other materials that can burn away from luminaire. Minimum 90°C supply conductors.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
oPeRatIng cHaRacteRIstIc
• Voltage Input: 120-277V 50/60Hz
• Operating Temperature: -20°C (-4°F) to 40°C (104°F)
Wattage & coLoR teMPeRatURe seLectIon
1x4 and 2x2
15W 19W 24W 29W 15W 19W 24W 29W 15W 19W 24W 29W
2x4
24W 29W 32W 39W 24W 29W 32W 39W 24W 29W 32W 39W
InstaLLatIon
WarninG: ALL units must be individually connected to the AC supply.
• Connect the BLACK fixture lead to the LINE supply lead.
• Connect the WHITE fixture lead to the COMMON supply lead.
• Connect the GROUND wire from fixture to SUPPLY ground.
RecesseD, sUsPenDIng anD sURFace aPPLIcatIon
Suspending application.
1 Recessed ceiling application. 2
Housing
1. Bend the clip
Access Plate
2. Install the hook
Tee-Grid
Bar
Part # BCB-22-lB4-8-CP3-MV-lVd Certification # BCB-22-lB4-8-CP3-MV-lVd
BCB-14-lB4-8-CP3-MV-lVd
BCB-24-lB4-8-CP3-MV-lVd
Fixture
5000K 4000K 3500K
15W 19W 24W 29W
5000K 4000K 3500K
24W 29W 32W 39W
LINE BLACK
COMMON WHITE
( + ) DIM V +
PURPLE LIGHT
FIXTURE
GRAY OR PINK
( - ) DIM V -
Vaux 12V
YELLOW
GROUND GREEN
Surface mount application.
3
D
C
Fixture
A
B
sensoR InstaLLIng
BCB-14-lB4-8-CP3-MV-lVd
Remove the lens and the outermost end cap. Use 2pieces M3x6 screws to fasten the motion sensor on the housing. and wiring as below wiring diagram. Then cover the lens and reinstall
BCB-24-lB4-8-CP3-MV-lVd
the end cap.
sensoR WIRIng DIagRaM
BatteRy InstaLLIng
Loosen the screws to open the driver box and use 2pcs 4*4*8
screws to fasten both end of the battery and emergency driver,
then wiring according to below wiring diagram.
BatteRy WIRIng DIagRaM
AC-L
AC-N
WarninG: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
nOTiCe: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV technician for help.
Surface
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Mount Kit
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
+12V
SENSOR
12V-/DIM-
DIM+
Dimming
Driver
SWITCH
BLACK
Driver -
LED DRIVER
Driver +
WHITE
Driver +
N 8
2
Driver -
7
EMERGENCY LED
LED +
L
1 5
DRIVER WITH
LED ARRAY
LED -
6
BATTERY
PG INDICATOR LIGHT
4
TEST SWITCH
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-ssLI (1-855-384-7754) www.etissL.com
YELLOW
+12V
GRAY OR PINK
LED
12V-/DIM-
DRIVER
VIOLET
DIM+
LED
7mm
5mm
SEPARATE TEST BUTTON
TEST SWITCH AND
INDICATOR LIGHT
CHARGING INDICATOR
TEST SWITCH
Different test switches and indicator
lights with a wall plate for option.