Publicité
Les langues disponibles
Les langues disponibles
90560838 ccs818 chain saw.qxd: chainsaw booklet new
STORAGE RECOMMENDATION
1. Store tool:
a.) with the battery pack removed and on the charger.
b.) in a place that is cool and dry away from direct sunlight and
excess heat or cold.
c.) out of the reach of children.
2. For prolonged storage such as over the winter, the battery pack
should be fully charged and then removed from the charger. It
should be charged again just prior to use.
LEAVING THE BATTERY PACK IN THE CHARGER
It is OK to leave battery packs on charge for long periods of time.
The charger has a maintenance mode which gives the battery pack
enough charge to stay "topped off". If however, the tool is not
expected to be needed for more than 30 days, unplug the charger
and store battery pack in a cool, dry location. NOTE: A battery pack
will lose its charge when kept off of the charger. If the battery pack
has not been kept on maintenance charge, it may need to be
recharged before use. A battery pack may also lose its charge if left
in a charger that is not plugged into an appropriate AC source.
IMPORTANT CHARGING NOTES
1. After normal usage, your battery pack should be fully charged in
6 to 9 hours. If the battery pack is run-down completely, it may
take up to 9 hours to become fully charged. Your battery pack
was sent from the factory in an uncharged condition. Before
attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below
+40°F(+4.5°C), or above +105°F (+40.5°C). This is important
and will prevent serious damage to the battery pack. Longest
life and best performance can be obtained if battery pack is
charged when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm to
touch. This is a normal condition and does not indicate a
problem.
4. If the battery pack does not charge properly—(1) Check current
at receptacle by plugging in a lamp or other appliance. (2)
Check to see if receptacle is connected to a light switch which
All manuals and user guides at all-guides.com
2/12/10
10:07 AM
10
Page 10
turns power off when you turn out the lights. (3) Move charger
and battery pack to a surrounding air temperature of 40°F
(+4.5°C) to 105°F (+40.5°C). (4) If the receptacle and
temperature are OK, and you do not get proper charging, take or
send the battery pack and charger to your local Black & Decker
service center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
NOT CONTINUE using unit with its battery pack in a depleted
condition.
6. The battery pack will reach optimum performance after being
cycled 5 times during normal usage. There is no need to run the
battery pack down completely before recharging. Normal usage
is the best method of discharging and recharging the battery
pack.
Preparing Your Chain Saw for Use
WARNING: Read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, fire
and/or serious personal injury.
Assembly
Installing the Guide Bar and Saw Chain
CAUTION: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it is
not running.
WARNING: Sharp moving chain. To prevent accidental
operation, insure that battery is disconnected from the tool
before performing the following operations. Failure to do this
could result in serious personal injury.
The saw chain and guide bar are packed separately in the carton inside the
scabbard. The chain has been placed on the guide bar at the factory to
insure that the teeth are facing in the proper direction when you first attach
it. Should the chain come off of the guide bar, refer to the section
"Replacing the Chain" for proper tooth orientation.
• Place the saw on a firm surface. Rotate the two allen head screws
(11) counterclockwise with the wrench (13) provided as shown in
figure D.
Publicité
