BorMann PRO BKD1355 Mode D'emploi page 2

EN
Safety instructions
Pictograms
Warning! Potential danger of life, risk of injury or tool damage are
possible by ignoring the general safety instructions.
Caution! Read the operating instructions to reduce the risk.
Wear safety goggles!
Wear ear-muffs!
Warning! Please read the instructions manual before using your Drill Press.
Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in an electric shock, fire
and/or serious injury. Keep all safety regulations and instructions in a safe place for future use.
Warning! To protect against electric shock, injury and fire the following basic safety precautions must be observed when using power tools.
Read and follow these Instructions before using the equipment and keep the safety information in a safe place.
Keep work area clean; Cluttered areas and benches invite injuries.
Consider work area environment; Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep work area well lit. Do not use
power tools in presence of flammable liquids or gases.
Guard against electric shock; Prevent body contact with grounded surfaces (e.g. pipes, radiators, ranges refrigerators).
Keep children away; Do not allow other persons to touch the equipment or cable, keep them away from your work area.
Store idle tools; When not is use, tools should be stored in dry, high, or locked-up place, out of the reach of children.
Do not force tool; It will do the job better and safer at the rate for which it was intended.
Use right tool; Do not force small tools or attachments to do the job of heavy duty tool. Do not use tools for purposes not intended.
Dress properly; Do not wear loose clothing or jewellery. They can be caught in moving parts. Νon-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
Use safety glasses; Also use face or dust mask if cutting operation is dusty.
Do not abuse cord; Never carry tool by cord or yank it to disconnect it from receptacle. Keep cord from heat, oil and sharp edges.
Secure work; Use clamps or a vice to hold work. It is safer than using your hand and it frees both hands to operate tool.
Do not overreach; Keep proper footing and balance at all times.
Maintain tools with care; Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
Disconnect tools; When not in use, before servicing, and when changing accessories.
Remove adjusting keys and wrenches; Form the habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
Avoid unintentional starting; Do not carry plugged-in too with finger on switch. Be sure switch is off when plugging in.
Outdoor use extension cords; When tool is used outdoors, use only extension cords intended for use outdoors and so marked.
Stay alert; Watch what you are doing. Use common sense. Do not operate the tools when you are tired.
Check damaged parts; Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise Indicated elsewhere in this
instructions manual. Have defective switches replaced by an authorized service-center. Do not use tool if switch does not turn it on and off.
Warning! The use of any other accessory or attachment other than recommended it this operating instruction manual may present a risk of personal
injury.
Have your tool repaired by an expert; This electric appliance is in accordance with the relevant safety rules repairing of electric appliances may be carried
out only by experts otherwise it may cause considerable danger for the user.
Connect the dust extraction device; Wherever there are facilities for fitting a dust extraction system, make sure it is connected and used.
Warning! This electric tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or dead y injuries, we recommend that persons with medical implants consult with their physician and the
manufacturer of the medical implant prior to operating the electric tool.
2
WWW.NIKOLAOUTOOLS.GR
Wear a breathing mask!
Use a hair net in order to cover
your hair.
Do not wear gloves!