Stanley FATMAX KFFMED1250 Mode D'emploi page 11

mum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
Tighten the knob (9).
u
Fitting an accessory (fig. B)
Clean and grease the shank (10) of the accessory.
u
Pull back the sleeve (11) and insert the shank into the tool
u
holder (5).
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked. The
u
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
To remove the accessory, pull back the sleeve (11) and
u
pull out the accessory.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (fig. D)
The tool can be used in three operating modes.
To operate the drilling mode selector (3), rotate it towards
u
the required position, as indicated by the symbols.
To operate the operating mode selector (4), push the
u
unlock button (16) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for screwdriv-
u
ing set the operating mode selector (4) to the
and the drilling mode selector (3) to the
Hammer drilling
For hammer drilling in masonry and concrete, set the
u
operating mode selector (4) to the
drilling mode selector (3) to the
mering, the tool should not bounce and run smoothly. If
necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
u
q
and chipping, set the operating mode selector (4) to the
s
position and the drilling mode selector (3) to the
position.
When changing from hammer drilling to chiselling, turn
u
the chisel to the desired position. If resistance is felt
All manuals and user guides at all-guides.com
(Übersetzung der ursprünglichen Anweisungen)
s
r
position
position.
s
s
position and the
position. When ham-
during mode change, slightly turn the chisel to engage the
spindle lock.
Switching on and off
Select the required speed by turning the speed selector
u
dial (2).
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch.
u
Brush monitor (fig.C)
Your tool has a built in system that monitors the health of the
brushes.
Green brush monitor indicator (17). The brushes are in
u
good condition.
Red brush monitor indicator (18). The brushes are warn
u
and need replacing, return your tool to an authorised
Stanley Europe Service Centre in order to to have the
brushes replaced.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Switch off and unplug the appliance/tool.
u
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
DEUTSCH
11