Preparation And Operation - Sammic GE-300 Mode D'emploi

1 FOREWORD...................................................................8
1.1 Introduction............................................................8
1.2 Use...........................................................................8

2 PREPARATION AND OPERATION............................8

2.1 Opening the packaging ........................................8
2.2 Installation..............................................................8
2.3 Wiring.....................................................................9
2.4 Operation ................................................................9
2.5 Operation in automatic mode..............................9
3 CONTROLS AND SAFETY DEVICES.........................9
3.1 Controls ..................................................................9
3.2 Mechanical safety devices ...................................9
3.3 Testing ....................................................................9
4 USING THE SLICER......................................................9
4.1 Operating procedure .............................................9
5 MAINTENANCE AND CARE OF THE SLICER .........9
5.1 Cleaning..................................................................9
5.2 Lubricating...........................................................10
6 SHARPENING OPERATIONS....................................10
6.1 Sharpening the bladE .........................................10
7 CLEANING AND MAINTENANCE...........................10
8 TRAINING....................................................................10
9 FEATURES...................................................................11
10 WIRING DIAGRAMS................................................11
1 FOREWORD
-This manual has been compiled in conformity with the
Machine Directive 89/392 - 89/109 - 91/398 - 91/368 -
93/44 - 89/336 - 92/31 - 73/23 - 93/68 CEE.
With it, the manufacturer intends to furnish the
customer with clear and concise instructions for the use
and maintenance of the machine, as well as information
regarding the safety devices with which it is fitted in
order assure maximum efficiency throughout its service
life.
-The slicers may be updated; this eventuality shall not
prejudice the explanations contained in the manual.
-Before starting up the slicer, you are advised to read
this manual carefully.
-Should this manual be damaged or lost, apply for a
copy from the manufacturer without delay.
-Many accidents are the result of insufficient familiarity
with the machine and its safety devices. Before starting
work, read the instructions herein carefully and follow
them to the letter.
1.1 Introduction
The Gear Drive Gravity slicers have been designed to
comply with the provisions of the European community
safety regulations. Consequently, each slicer is fitted
with a plate featuring the "CE" mark attesting to the
product's conformity with said provisions.
1.2 Use
These slicers have been manufactured to slice cooked
and raw charcuterie, warm and cold meats, bread and
cheese, stoneless fruit and vegetables. They can slice
thicknesses up to 23 mm.
ENGLISH
They are not suitable for cutting frozen goods,
charcuterie and meat on the bone or fruit with stones.
Any attempt to slice said products or similar foods may
result in serious damage to the machine and shall
cause the warranty to become void.
2 PREPARATION AND OPERATION
On receiving the box containing the slicer, make sure
that it is intact and has not been damaged during
transit.
2.1 Opening the packaging
1- Cut and remove the plastic straps;
2 - Remove the metal staples;
3 - Lift the box off vertically, locate the user guide,
maintenance manual and the four feet;
4 - Using a 13mm spanner, unscrew the bolts securing
the machine to the pallet;
5 - Remove the polyethylene bag and screw on the four
feet;
6 - Lift the machine: two people are required to handle
the machine, using the feet as handholds;
7 - Check the contents of the packaging, making sure
they correspond to the specifications on the documents;
WARNING: THE PACKAGING CAN BE DISPOSED OF
AS MUNICIPAL SOLID WASTE: COMPLY WITH THE
LAW DISPOSITIONS IN FORCE IN THE PLACE OF
INSTALLATION. DO NOT LITTER: DISPOSE OF THE
PARTS MAKING
APPROPRIATELY
2.2 Installation
Place the slicer on a smooth, flat and stable surface.
Any unevenness of the surface on which the machine is
rested can be compensated using the adjustable feet.
In the event the motor ventilation area faces a wall,
8
UP THE PACKAGING