TEFAL Rowenta PU2840 Mode D'emploi page 5

Connection issues
In case of pairing issues between the appliance and your domestic Wi-Fi network, refer to the
information listed on the following link:
https://www.compatibility.groupeseb.com/CompatibilityList-Pureair-Rowenta.pdf
https://www.compatibility.groupeseb.com/CompatibilityList-Pureair-Tefal.pdf
OPERATION
In order to achieve the best purification effect, your purifier should be more than 60cm away from
the wall.
Power « Start/Stop (1) »
– Press this button to turn the air purifier on/off.
« Speed selection (2) »
– You can choose manually the purification speed from speed 1 to Speed 6.
« Auto day mode button (4) »
– The purification speed is set to speed 2, speed 4 or speed 5 according to air quality level.
– If the air quality level is excellent then the device does not run.
« Auto Night Mode (5) »
– The purification speed is set to speed 1, speed 2 or speed 3 according to air quality level.
– If the air quality level is excellent then the device does not run.
– The lights on the device turn off automatically after 5 seconds. To turn the control panel back
on, press one of the buttons.
« Child lock (3) »
– The lock system prevents the purifier from being accidentally mis-set during operation.
– To activate it, press the button (3) for 3 sec until the locked control panel indicator turns on.
To exit this mode, press the button (3) again for 5 seconds, until the indicator turns off.
When selected, the other buttons are locked.
• Indication of air quality
Air quality indicator is the light cercle around start/ stop button. Air quality indicator (7) is located
at the « Control panel (A) » of the appliance. The LED will indicate the air quality level:
Air Quality
Excellent
Slight pollution
Moderate pollution
High pollution
CARE & MAINTENANCE
Before performing any maintenance work, always switch off the air purifier using the « start/ stop button
(1) » and unplug it. Use a damp cloth to clean the surface of the product.
Important: Do not use any abrasive materials, as these may damage the surface of the product.
8
Air quality level color
Blue
Green
Yellow
Red
FILTER
This appliance is equipped with 3 types of filters:
Prefilter
Frequency of cleaning/replacing the filter :
Filter
Pre-filter Clean (remove dust)
3-in-1 pre-filter, allergy+ filter
and active carbon
The recommended frequency for replacing the filter may vary depending on the duration of use
and the operating environment.
IMPORTANT:
The filter change indicator (6) is lighted when the filter needs to be replaced. Once the filter has
been replaced, hold down the button for 5 seconds.
Forced reset:
If you have replaced the filter before its end of life, force the reset of filter cycle:
1. Hold the filter change indicator (6) for 5 seconds.
2. The indicator is lighted. Hold down the button for 5 seconds, to reset the filter cycle.
« TIPS FOR CHANGING FILTERS »
• Avoid handling used filters if you suffer from allergies or asthma.
• Wear gloves when changing the filters, or wash your hands well afterwards.
• Put used filters directly into a closed, air-tight bag before throwing them away to
avoid spreading pollutants.
POLLUTION SENSOR
The particles sensor need to be cleaned regularly (every 2 months) and appropriately.
Make sure you turn off and unplug the appliance before cleaning the pollution sensors and follow
the recommendations below:
1. Clean the air inlet and outlet using a soft brush or cloth.
2. Open the sensor cover located at the back of the appliance.
3. Lightly wet a cotton swab and remove any dust from the lens and the inlet/outlet. Wipe using
a dry cotton swab.
4. Clean the sensor using a soft brush or vacuum cleaner.
5. Replace the sensor cover
Active Carbon Particle filter NanoCaptur+
filter
Action Cycles
Every 2 to 4 weeks
Every 12 months or when the
Replace
filter change indicator is lighted
EN
filter
9