Toshiba Carrier MMY-MAP0726FT6P-UL Manuel Du Propriétaire page 11

◆ To stop swinging
1
Push the button at the desired
position while the louver is swinging.
• Push the button repeatedly to change
the louver position again.
* However, even if the button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
▼ Indications when swinging is stopped
FAN/HEAT COOL/DRY
In this case, push the button again after 2
seconds.
• In Cool/Dry operation, the louver does not stop
as it directs downward. If stopping the louver as
it directs downward during swing operation, it
stops after moving to the third position from the
highest position.
Indications when swinging is stopped
▼
FAN/HEAT COOL/DRY
operation operation
◆ Unit select
• When two or more indoor units are controlled with
one remote control, the louver direction can be set
for each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all
indoor units in the control group can be controlled
simultaneously.
• Each time the (left side of the button) is
pushed, the indication changes as follows:
No Unit No. Unit No.
display 1-1 1-2
Unit No. Unit No.
1-4 1-3
19-EN
Carrier 1122002001 EN FR.indb 10 Carrier 1122002001 EN FR.indb 10
4-way cassette type only
■
◆ To set the louvers individually
1
Push the button (left side of the
button) during running to select a unit.
The unit number changes each time the button is
pushed.
Unit No. Unit No. Unit No.
1-1 1-2 1-3
No Unit No.
display 1-4
• When no unit number is displayed, all units are
selected.
2
Push the button (right side of the
button) to select a louver.
Each time the button is pushed, the indicator on
the left of the remote control changes as follows:
No
display
* When no louver number is displayed, all 4
louvers are selected.
Louver No.
Electrical control box
03
Refrigerant
pipe
04 02
Drain pipe
01
3
Push the button to confirm the
direction of the selected louver.
Each time the button is pushed, the indication
changes as follows:
(1) (2) (3) (4)
(7) (6) (5)
* When cooling or drying, (4) and (5) are not
displayed.
◆ Setting the swing pattern
1
Push and hold the FIX for at least 4
seconds while the operation is stopped.
blinks.
2
Push the button (left side of the
button) to select a unit.
The unit number changes each time the button is
pushed.
Unit No. Unit No. Unit No.
1-1 1-2 1-3
No Unit No.
display 1-4
The fan of the selected unit runs, and the louver
swings.
3
Push the buttons to select a swing
type.
Swing code
Swing code Movement pattern
Standard swing
0001
(factory default)
0002 Dual swing
0003 Cyclic swing
REQUIREMENT
Do not set "0000".
(The louver may be damaged.)
– 10 –
4
Push the button.
5
Push the button to finish the setting.
▼ Standard swing
All four louvers swing simultaneously at the same
angle.
Swing
Dual swing (Recommended for heating)
▼
• Adjoining louvers alternately point horizontally and
downward to heat the room evenly.
• Air blown downward reaches the fl oor, and air blown
horizontally is spread to circulate heat.
Horizontal
Horizontal
Downward
Downward
Horizontal
Horizontal
Downward
Downward
6/22/16 2:10 PM 6/22/16 2:10 PM
EN
EN
EN
ES
20-EN