Clatronic KM 3099 Mode D'emploi page 42

CAUTION:
Do not use the mixer and the grater bowl at the same
time.
Mains Lead
Unwind the required mains lead from the base.
Initial Operation
Mixer function
1. The grater bowl (10) must be mounted as described in the
section „Positioning the Grater Bowl" (without tool).
2. Chop the food to be mixed into small pieces.
3. Fill the mixer vessel (3) with the food to be mixed (min. 0.2 l
- max. 1.5 l). Never fi ll with hot food or hard ingredients such
as potatoes, ice, coffee beans, nuts, and so on. Do not
overfi ll! Do not exceed the maximum quantity stated on the
mixing bowl!
CAUTION: SAFETY SWITCH!
The device only works if the grater bowl (10) with lid is
also in place.
4. Put the lid (4) in place and turn it tight.
5. Close the lid with the lock (5), paying attention to the reces-
ses. Turn the lock until it is tight.
6. Place the mixing bowl (3) in position as described under
„Positioning the Mixing Bowl".
7. If you wish to fi ll in more food to be mixed you can remove
the lid and cover. Switch the device off beforehand. Remove
the lid (4) of the mixer vessel and fi ll with the desired ingredi-
ents.
WARNING:
Do not reach into the mixer vessel, as the underlying
blade may cause injuries.
8. Place the lid on the mixer vessel again. Do not use the mixer
when empty or without the lid. Ensure that the function
switch is in the „0" position.
9. Insert the plug in a duly installed 230 V/50 Hz socket.
10. Switch the device on (Level 1 or 2 etc.) or use pulse operati-
on (PULSE).
11. The mixing bowl must be held fi rmly in place during mixing.
12. For constant mixing (continuous mode):
When the device is operated on levels 1 to 4 the switch
locks into place in the respective position.
Level 1 = low rpm
Level 4 = high rpm
To switch the device off, turn the switch back to the „0"
position.
For pulse mode (mixing at brief intervals) shift the switch
to „0" position. The appliance is off now. Please press the
PULSE (20) button. Keep the button pressed down in this
position according to the desired interval length. When
the button is released, it automatically returns to the „off"
position.
13. In order to remove the mixer jug turn it counterclockwise.
42
05-KM 3099 42
14. Clean the used parts as described in „Cleaning".
Mixing bowl
• The cover of the mixer drive (7) must be mounted as descri-
bed above.
• Mount the grater bowl as described under „Positioning the
Mixing Bowl".
• Place the locating pin over the drive shaft (Illustration 5).
The metal point faces upwards.
• Never use more than one utensil at a time.
Dough kneading and beating
1. Take the plastic blade (16) for preparing the dough and
attach it to the locating pin. Then press the plastic blade down
as far as it will go (Illustration 6).
2. Now fi ll in your ingredients. Please note the markings on the
processor bowl and do not fi ll it above them (min 0.2 l - max.
0.8 l).
3. Place the lid in position on the processor bowl. Turn it tight
until it is clearly heard to lock in place (Illustration 7).
4. Close the opening in the lid with the stopper (17).
5. Insert the plug into a 230 V / 50 Hz socket installed accor-
ding to existing regulations and with earthing protection.
Switch on the appliance and set a speed between 1 and 3
(See table) with switch (1).
When the device is operated on levels 1 to 4 the switch
locks into place in the respective position.
Level 1 = low rpm
Level 4 = high rpm
To switch the device off, turn the switch back to the „0"
position.
For pulse mode (Operating at short intervals) shift the switch
to „0" position. The appliance is off now. Please press the
PULSE (20) button. Keep the button pressed down in this
position according to the desired interval length. When
the button is released, it automatically returns to the „off"
position.
With this device it is possible within a very short time:
• up to 45 0 g of heavy dough (bread or pastry),
• beat up to 800 g of crepe or waffl e batter,
• beat up to 800 g of light dough (e.g. for cookies).
NOTE:
Do not exceed the short operation times stated in the table
when kneading the dough!
6. After kneading/stirring turn the switch (1) back to position
„0" as soon as a small amount or ball of dough has formed.
Then remove the mains plug.
7. Turn the lid to the left and remove it from the processor
bowl.
8. Pull the blade off from the locating pin.
9. Release and remove the grater bowl and the locating pin.
The fi nished dough can be released from the sides and with
a spatula (18) and taken out of the bowl.
10. Clean the used parts as described in „Cleaning".
05.10.2006, 11:05:35 Uhr