Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
6.
WIRING: Plug fan power supply into appropriate AC outlet (7).
7.
Reinstall door, air outlet grill, and projector pole mount components (for HRCB22P) after fan kit installation and
wiring is complete. Refer to PD-3032.
7
FIGURE
G
HRCB22 & HRCB22P FAN KIT INSTALLATION INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes,
communications standards, the following instructions, and any instructions included with individual devices.
NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC
and CE Code requirements.
FOR MODEL HRCB22 REMOVE DOOR AND AIR OUTLET GRILL. FOR MODEL HRCB22P REMOVE DOOR AND PROJECTOR
POLE MOUNT ASSEMBLY.
(REFER TO INSTALLATION INSTRUCTIONS PD-3032 INCLUDED WITH HRCB22 & HRCB22P. AIR OUTLET GRILL REMOVAL
SHOWN IN STEP 2 BELOW).
1.
Install the two supplied #8-32 X 1/4" long pan head screws (1) (2 turns only) into fan mounting bracket (2) leaving a
minimum gap of .15" under the screw heads as shown in FIGURE A and A1.
NOTICE: Screws installed without keeping the minimum gap of .15" under the head, will hinder fan bracket assembly
installation.
THRU SLOT
2
1
2.
Remove air outlet grill (3) by removing two #4-40 hex nuts (4). Push fan kit assembly (2) to top surface of ceiling box
in the corner next to the AC box. Make sure the assembly is oriented as shown in FIGURE B1.
3
4
Wiring Device - Kellems
Hubbell Incorporated (Delaware)
40 Waterview Dr.
Shelton, CT 06484
1-800-288-6000
www.hubbell-wiring.com
PD3037
04/23
THRU SLOT
1
.15 MIN
2
Figure A1
FIGURE
A
2
FIGURE
B
Figure B1
ENGLISH
Publicité
Manuels Connexes pour Hubbell HRCB22
Sommaire des Matières pour Hubbell HRCB22
- Page 1 NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC and CE Code requirements. FOR MODEL HRCB22 REMOVE DOOR AND AIR OUTLET GRILL. FOR MODEL HRCB22P REMOVE DOOR AND PROJECTOR POLE MOUNT ASSEMBLY. (REFER TO INSTALLATION INSTRUCTIONS PD-3032 INCLUDED WITH HRCB22 & HRCB22P. AIR OUTLET GRILL REMOVAL SHOWN IN STEP 2 BELOW).
- Page 2 Rotate the top of the fan kit assembly (2) to engage the screw tabs under the screw heads as shown below in FIGURE E. With the fan assembly (2) positioned as shown in FIGURE C, angle the bottom to engage the side tabs (5) of the fan NOTICE: Be careful not to pinch fan wires.
- Page 3 NECMD et du Code canadien de l' lectricit . POUR LE MOD LE HRCB22, ENLEVER LA PORTE ET LA GRILLE DE SORTIE D'AIR. POUR LE MOD LE HRCB22P, RETIRER LA PORTE ET L'ENSEMBLE DE MONTAGE DU PROJECTEUR.
- Page 4 L'ensemble ventilateur (2) tant positionn comme la FIGURE C, incliner le bas pour engager les pattes lat rales (5) Faire pivoter le haut de l'ensemble ventilateur (2) pour engager les pattes de vis sous les t tes de vis selon la FIGURE E. du support de l'ensemble ventilateur dans les encoches (6) des supports avec d bouchures des deux c t s.
- Page 5 Figure B1 Wiring Device - Kellems HUBBELL DE M XICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra. Hubbell reparar o reemplazar el Hubbell Incorporated (Delaware) art culo a su juicio en un plazo de 60 d as.
- Page 6 Gire la parte superior del conjunto del kit de ventilador (2) para enganchar las leng etas de los tornillos debajo de las Con el ensamblaje del ventilador (2) colocado como se muestra en la FIGURA C, incline la parte inferior para cabezas de los tornillos, como se muestra a continuaci n en la FIGURA E.