Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
6.
WIRING: Route fan wiring along inside wall (5). Secure wiring to shelf bracket (6) using supplied cable clamp and
hardware. Plug fan power supply into appropriate AC outlet.
5
6
7.
Reinstall door and projector pole mount components after fan kit installation and wiring is complete. Refer to
PD-3027.
5
FIGURE
G
HRCB12 & HRCB12P FAN KIT INSTALLATION INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing or servicing.
NOTICE: For installation by a qualified electrician in accordance with all national and local electrical codes,
communications standards, the following instructions, and any instructions included with individual devices.
NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC
and CE Code requirements.
FOR MODEL HRCB12 REMOVE DOOR. FOR MODEL HRCB12P REMOVE DOOR AND PROJECTOR POLE MOUNT ASSEMBLY.
(REFER TO INSTALLATION INSTRUCTIONS PD-3027 INCLUDED WITH HRCB12 & HRCB12P)
1.
Install the two supplied #8-32 X 1/4" (1) long pan head screws (2 turns only) into fan mounting bracket (2) leaving a
minimum gap of .15" under the screw heads as shown in FIGURE A and A1.
NOTICE: Screws installed without keeping the minimum gap of .15" under the head, will hinder fan bracket assembly
installation.
2
THRU SLOT
1
2.
Push fan kit assembly to top surface of ceiling box. Make sure the assembly is oriented as shown in FIGURE B.
Wiring Device - Kellems
Hubbell Incorporated (Delaware)
40 Waterview Dr.
Shelton, CT 06484
1-800-288-6000
www.hubbell-wiring.com
PD3036
04/23
.15 MIN
THRU SLOT
1
Figure A1
FIGURE
A
FIGURE
B
ENGLISH
2
Publicité
Manuels Connexes pour Hubbell HRCB12
Sommaire des Matières pour Hubbell HRCB12
- Page 1 NOTICE: Ensure data/communications circuits are separated from lighting/power circuits in accordance with the NEC and CE Code requirements. FOR MODEL HRCB12 REMOVE DOOR. FOR MODEL HRCB12P REMOVE DOOR AND PROJECTOR POLE MOUNT ASSEMBLY. (REFER TO INSTALLATION INSTRUCTIONS PD-3027 INCLUDED WITH HRCB12 & HRCB12P) Install the two supplied #8-32 X 1/4"...
- Page 2 Push the top of the fan kit assembly to rotate into position. The screw tabs of the knockout brackets should be With the fan assembly (2) positioned as shown in FIGURE C, angle the bottom to engage the side tabs (3) of the fan positioned under the screw heads of the fan kit assembly as shown below in FIGURE E, detail M.
- Page 3 AVIS - S'assurer que les circuits de communication/des donn es sont s par s des circuits d'alimentation/d' clairage conform ment aux exigences du NECMD et du Code canadien de l' lectricit . POUR LE MOD LE HRCB12, ENLEVER LA PORTE. POUR LE MOD LE HRCB12P, RETIRER LA PORTE ET L'ENSEMBLE DE MONTAGE DU PROJECTEUR.
- Page 4 Avec l'assemblage du ventilateur (2) positionn comme illustr la FIGURE C, inclinez le bas pour engager les Pousser le haut de l'ensemble ventilateur pour le faire pivoter en position. Les pattes de vis des supports avec languettes lat rales (3) du support de l'assemblage du ventilateur avec les encoches (4) dans les supports d fon ables d bouchures doivent tre positionn es sous les t tes de vis de l'ensemble ventilateur, FIGURE E ci-dessous, d tail M.
- Page 5 FIGURE Wiring Device - Kellems HUBBELL DE M XICO garantiza este producto, de estar libre de defectos en materiales y mano de obra por un a o a partir de su compra. Hubbell reparar o reemplazar el Hubbell Incorporated (Delaware) art culo a su juicio en un plazo de 60 d as.
- Page 6 Con el ensamblaje del ventilador (2) colocado como se muestra en la FIGURA C, incline la parte inferior para Empuje la parte superior del conjunto del kit de ventilador para girar a su posici n. Las leng etas de los tornillos de enganchar las leng etas laterales (3) del soporte del ensamblaje del ventilador con las muescas (4) en los soportes las placas ciegas deben colocarse debajo de las cabezas de los tornillos del conjunto del kit de ventilador, como se ciegos en ambos lados.