Makita BTD125 Manuel D'instructions page 7

ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing or removing driver bit or socket
bit (Fig. 7)
Use only bits that has inserting portion shown in the
figure.
For tool with shallow bit hole
Use only these type of bit. Follow the
A=12 mm
procedure (1).
B=9 mm
(Note) Bit-piece is not necessary.
For tool with deep bit hole
A=17 mm To install these types of bits, follow the
B=14 mm procedure (1).
To install these types of bits, follow the
A=12 mm procedure (2).
B=9 mm (Note) Bit-piece is necessary for installing
the bit.
1. To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will
go. Then release the sleeve to secure the bit. (Fig. 8)
2. To install the bit, pull the sleeve in the direction of the
arrow and insert the bit-piece and bit into the sleeve
as far as it will go. The bit-piece should be inserted
into the sleeve with its pointed end facing in. Then
release the sleeve to secure the bit. (Fig. 9)
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
• If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
bit according to the instructions above.
• After inserting the bit, make sure that it is firmly
secured. If it comes out, do not use it.
OPERATION (Fig. 10)
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between
fastening torque and fastening time is shown in the
figures. (Fig. 11 - 14)
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
NOTE:
• Use the proper bit for the head of the screw/bolt that
you wish to use.
• When fastening screw M8 or smaller, carefully adjust
pressure on the switch trigger so that the screw is not
damaged.
• Hold the tool pointed straight at the screw.
All manuals and user guides at all-guides.com
• If you tighten the screw for a time longer than shown in
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1. When the battery cartridge is discharged almost
2. Driver bit or socket bit
3. Bolt
4. The manner of holding the tool or the material of
5. Operating the tool at low speed will cause a reduction
MAINTENANCE
• Always be sure that the tool is switched off and the
• Never use gasoline, benzine, thinner, alcohol or the
Replacing carbon brushes (Fig. 15)
Replace when they wear down to the limit mark. Keep the
carbon brushes clean and free to slip in the holders. Both
carbon brushes should be replaced at the same time. Use
only identical carbon brushes.
Use a screwdriver to remove two screws then remove the
rear cover. (Fig. 16)
Raise the arm part of the spring and then place it in the
recessed part of the housing with a slotted bit screwdriver
of slender shaft or the like. (Fig. 17)
Use pliers to remove the carbon brush cap of the carbon
brushes. Take out the worn carbon brushes, insert the
new ones and replace the carbon brush cap in reverse.
(Fig. 18 & 19)
Make sure that the carbon brush cap have fit into the
holes in brush holders securely.
Reinstall the rear cover and tighten two screws securely.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
• These accessories or attachments are recommended
the figures, the screw or the point of the driver bit may
be overstressed, stripped, damaged, etc. Before
starting your job, always perform a test operation to
determine the proper fastening time for your screw.
completely, voltage will drop and the fastening torque
will be reduced.
Failure to use the correct size driver bit or socket bit
will cause a reduction in the fastening torque.
• Even though the torque coefficient and the class of
bolt are the same, the proper fastening torque will
differ according to the diameter of bolt.
• Even though the diameters of bolts are the same,
the proper fastening torque will differ according to
the torque coefficient, the class of bolt and the bolt
length.
driving position to be fastened will affect the torque.
in the fastening torque.
CAUTION:
battery cartridge is removed before attempting to
perform inspection or maintenance.
like. Discoloration, deformation or cracks may result.
CAUTION:
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
7