NightStick Fortem XPP-5466 Mode D'emploi page 2

Image 4
INSTALLING THE 5466 ON TO THE HELMET
SCAN FOR
MOUNTING
INSTRUCTION
VIDEO
Once the batteries have been installed and the proper orientation and/or angle of the
Mount has been set, the light is ready to be attached to the Fire Helmet or Hard Hat. The
light comes with two 5/16" - 18 x 1/4" Brim Mounting Allen Set Screws pre-installed. These
two Allen Set Screws are designed to be used with the thicker brim found on most Fire
Helmets. (Image 7)
It may be necessary to switch these two Allen Set Screws with the 5/16" - 18 x 3/8"
set if the thickness of the brim of the helmet or Hard Hat makes it impossible to use the
shorter set. (Image 8)
Position the mount over the edge of the brim and tighten the appropriate set of Allen
Set Screws using the included 5/32" Allen Wrench. (Image 9)
Use included mounting shim as necessary to secure the mount to the helmet.
Image 7
CAUTION: Be careful when tightening the Allen Set Screws. Do not over-tighten.
Doing so may damage or crush the brim of the Fire Helmet or Hard Hat. These
two Allen Set Screws should only be tightened enough to prevent the mount
from coming loose from the helmet. Over time these screws may come loose.
Periodically check and re-tighten as needed.
SUGGESTION: Application of a thread locking solution (such as Loctite®
Threadlocker Blue) may be applied to secure these Allen Set Screws. Do not use the
"red" version of this product as it is designed for a more permanent installation and would
make it diffi cult to remove these Allen Set Screws in the future.
SETTING THE ANGLE OF THE MULTI-ANGLE MOUNT
NOTE: THIS PRODUCT IS NOT DESIGNED TO SWIVEL BACK AND FORTH ONCE
THE ANGLE HAS BEEN SET. THE USER WILL NEED TO LOOSEN THE ANGLE
LOCK SOCKET HEAD CAP SCREW TO REPOSITION THE ANGLE.
To adjust the angle of the light, loosen the Angle Lock Socket Head Cap Screw using
the included 5/32" Allen Wrench. (Image 10)
Select the angle and then tighten the Angle Lock Socket Head Cap Screw securely.
(Image 11)
Test to make sure that the angle will not change and continue tightening as needed.
Image 10
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • USA • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
All manuals and user guides at all-guides.com
Image 5 Image 6
Image 8 Image 9
Image 11
OPERATION
The 5466 has seven lighting modes:
y Constant-on high-brightness fl ashlight
y Medium-brightness fl ashlight
y Low-brightness fl ashlight
y Constant-on high-brightness fl oodlight
y Medium-brightness fl oodlight
y Low-brightness fl oodlight
y Constant-on Dual-Light mode
The 5466 has two switches, the fl ashlight switch (closest to the front of the light)
and the fl oodlight switch (closest to the rear of the light) providing access to all modes.
CONSTANT-ON FLASHLIGHT
Press the fl ashlight switch (closest to the front of the light) until it clicks and then
release for constant-on fl ashlight in high-brightness mode. Press and release this same
switch again to turn the light off.
SELECT FLASHLIGHT BRIGHTNESS LEVEL
Press and hold down the fl ashlight switch. The fl ashlight will cycle from high to
medium to low and then back up again at a rate of approximately one mode per second.
The light will continue to cycle up and down through the various modes as long as the
fl ashlight switch is held down. When the desired brightness level is reached, simply
release the fl ashlight switch, and the light will remain in that brightness mode. Pressing
and holding the fl ashlight switch again will cause the light to cycle from whatever mode it
is currently in. Press and release the fl ashlight switch to turn the light off.
CONSTANT-ON FLOODLIGHT
Press the fl oodlight switch (closest to the rear of the light) until it clicks and then
release for constant-on fl oodlight in high-brightness mode. Press and release this same
switch again to turn the light off.
SELECT FLOODLIGHT BRIGHTNESS LEVEL
Press and hold down the fl oodlight switch. The fl oodlight will cycle from high to
medium to low and then back up again at a rate of approximately one mode per second.
The light will continue to cycle up and down through the various modes as long as the
fl oodlight switch is held down. When the desired brightness level is reached, simply
release the fl oodlight switch, and the light will remain in that brightness mode. Pressing
and holding the fl oodlight switch again will cause the light to cycle from whatever mode it
is currently in. Press and release the fl oodlight switch to turn the light off.
DUAL-LIGHT
Dual-Light allows the user to turn on both the Flashlight and the Floodlight, at the
same time. Simply press each switch to turn on each lighting mode. Both the Flashlight
and the Floodlight are now running. Press and release each switch to turn the light off.
WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials for the original purchaser's lifetime. The Limited Lifetime Warranty includes
the LEDs, housing and lenses. Rechargeable batteries, chargers, switches, electronics
and included accessories are warranted for a period of two years with proof of purchase.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty installation
and lightning damage are excluded.
We will repair or replace this product should we determine it to be defective. This
is the only warranty, expressed or implied, including any warranty of merchantability or
fi tness for a particular purpose.
For a complete copy of the warranty, go to www.nightstick.com/nightstick-product-
support/warranties. Retain your receipt for proof of purchase.
INS-XPP-5466-16
09-27-2018