Télécharger Imprimer la page

IKEA UPPLEVA Mode D'emploi page 13

Masquer les pouces Voir aussi pour UPPLEVA:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 48
Important:
If the remote control is not used for a long
period, remove the batteries and store
them properly. Handle damaged or leaking
batteries carefully. If your remote control
has two batteries, do not mix new and old
batteries. Batteries shall not be exposed
to excessive heat such as sunshine, fire or
the like. Danger of explosion if battery is
incorrectly replaced. Replace only with the
same or equivalent type recommended by
the manufacturer. Discard used batteries
according to manufacturer's instructions.
Refer to your local recycling or waste
disposal rules and contact a local waste
disposal vendor to dispose of used batteries.
If the batteries in your remote control
are run down you can use the buttons on
your TV. In TV mode, they have the same
functions as the corresponding buttons on
the remote control. In the menus they have
the following functions:
CH
CH
VOL
VOL
MENU/
OK/
Switch the TV on and off
1. When powered on, the TV will be turned
on directly or be in standby mode. If
the TV is in standby mode, press the
or POWER/
button on the TV or the
button on the remote control to turn
it on.
2. To put the TV into standby mode, press
the
or POWER/
the
button on the remote control. The
TV remains powered up, but with low
energy consumption.
3. To switch the TV off, unplug the mains
plug from the mains outlet.
(*On certain models, you have to turn on
the power switch first.)
Initial setup
Initial setup involves selecting all the
settings required to be able to search
for and store all the Analogue and digital
channels you can receive.
All manuals and user guides at all-guides.com
MENU
OK
button on the TV or
Make sure the TV is switched on and follow
all the steps below in the order given.
Note: If the channel search retrieved only
the analogue channels it could be caused by
weak broadcasting signals and therefore is
not covered by the manufacturer warranty.
Manufacturers cannot be held responsible
for the lack of or weak broadcasting signals
that can be found in some areas.
The first time you switch the TV on, the
Initial Setup wizard opens, which guides
you through the initial setup process. (Refer
to Figure 1.) Press OK to start your initial
setup.
1. Press
/
to select your language, then
press
OK/
to enter the next step.
/
2. Press
to select your country, then
press
OK/
to enter the next step.
Note: If you select France, you will have
to enter the Password Setting menu here
in order to set a password. Use the
buttons to enter a four-digit number for
your password. (0000 is too simple to be set
as your password.) Re-enter the same code
to confirm the password. After that, you will
enter the next step automatically. (In this
step, you can only press
the previous step.)
/
3. Press
to select your tuner mode
Antenna or Cable or Satellite. (Note:
For some models, this option may not be
available.)
Select Antenna.
OK/
• Press
to enter.
• Select Digital & Analogue, Digital or
Analogue, then press
• Press
/
to select Scan, then press
OK/
to start the automatic search for all
DVB-T digital and/or analogue channels.
Select Cable.
OK/
• Press
to enter.
• Select Digital & Analogue, Digital or
Analogue, then press
• Press
/
to select Scan, then press
OK/
to directly start your initial setup or
enter below step.
• Select Full if available to search for and
store all DVB-C digital and analogue
channels.
• You may select another advanced
scan mode if available (for example,
Advanced), then configure proper cable
information as described below. Use the
digit
buttons to adjust the values for
frequency, symbol rate and network ID;
11
digit
BACK
to return to
OK/
.
OK/
.

Publicité

loading