Publicité
Connection
Anschluß
Raccordement
Aansluiting
Conexión
Collegamento
Ansluiting
Tilslutning
Liitäntä
Black
Schwarz
Noir
Zwart
Negro
Nero
Svart
Sort
Musta
1. Remove the ending part of the vinyl covering from the cut.
2. Twist the wires.
1. Entfernen Sie dan Endstück der Vinylhüle von dem geschnittenen
Teil.
2. Drehen Sie die Kabel.
1. Enlever la pertie d'extrémité du recouvrement vinylique de la
partie déoupée.
2. Tordre les fils.
1. Snijd het laatste gedeelte van de vinylmantel af en verwijder.
2. Draai de draadkernen ineen.
1. Quitar la parte de la extremidad de la cubierta de plástico de la
parte cortada.
2. Torcer los alambres.
1. Rimuovete l'estremità della copertura in plastica dalla parte
tagliata.
2. Torcete i fili.
1. Dra loss den avskurna delen av isoleringen från kabeländen.
2. Tvinna trådarna.
1. Fjern enden af vinyl-isoleringen, hvor den er klippet af.
2. Sno trådene.
1. Irrota muovipeitteen loppupää uurteesta.
2. Kierrä johdot.
All manuals and user guides at all-guides.com
Press
Drücken
Appuyer
Indrukken
Presionar
Premere
Tryck
Tryk
Paina
CONNECTION
• Connect the LEFT speaker terminals of the amplifier to the
LEFT terminals of the speaker and RIGHT to RIGHT using the
attached speaker cords as shown in the figure making sure
polarity is correct; (+) to (+) and (–) to (–). Connect the black
speaker wire to the (–) terminal.
• Turn off power to the whole system before connecting the
speakers to the amplifier.
• The nominal impedance of the SP-MD9 is 6 ohms. Connect
them to an amplifier with the load impedance of 6 ohms speak-
ers.
• The maximum power handling capacity of the SP-MD9 is 50
watts. Excessive input will result in abnormal noise and pos-
sible damage. In cases where the signals described below
are applied to the speakers, even if the signals are below the
maximum allowable input, they may cause an overload and
burn the wiring of the speakers. Be sure to lower the amplifier
volume beforehand.
1) Noise during FM tuning.
2) High level signals containing high frequency components
produced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other compo-
nents on and off.
4) Click noise produced when connecting or disconnecting
cords with the power on.
5) Click noise produced when the cartridge is replaced with
the power on.
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch elec-
tronically produced musical instrument sound.
8) Howling when using a microphones.
SPECIFICATIONS
Type
Speakers
Woofer
Mid Range
Tweeter
Power Handling Capacity : 50 watts
Impedance
Frequence Range
Sound Pressure Level
Dimensions (W x H x D)
Mass
Accessories
Design and specifications subject to change without notice.
4
: 3-way 3-speaker bass-reflex type
(Magnetically-shielded type)
: 15 cm (5-15/16") cone x 1
: 6 cm (2-3/8") cone x 1
: 2 cm (13/16") dome x 1
: 6 ohms
: 43 Hz-20,000 Hz
: 86 dB/w·m
: 210 x 345 x 249 mm
(8-5/16" x 13-5/8" x 9-13/16")
:3.4 kg (7.5lbs) each
: Speaker cord ................ 2
Publicité
