RCA RCR812 Mode D'emploi page 5

10. To confirm that the component key is programmed with the correct code for
maximum functionality, test the component. If some of the features of your
component do not work, different codes in the list can be tried until you find the
code that allows the remote to control the majority of your component's functions.
See section entitled "Testing the Code for Maximum Functionality."
Code Retrieval
Once you've programmed the remote to control your components, record the codes
for future reference. If you used the Direct Code Entry method, just make a note of
the codes you programmed in the boxes below. If you used one of the Code Search
methods to program your remote or if you used the Direct Code Entry method but
don't remember the code, you need to retrieve each component's four-digit code.
Noting the actual code will save you time if you ever need to program the remote
again (e.g., if programming is lost when you change the batteries). If the codes are
recorded, you can use the Direct Code Entry method to reprogram your remote.
1. Press and hold the component key whose code you
wish to retrieve. The illuminated ON·OFF key
turns on.
2. While holding the component key down, press and
hold the INFO key. The illuminated ON·OFF key
turns off.
3. After holding down both keys for three seconds, the
illuminated ON·OFF key turns back on.
4. Release both keys. The illuminated ON·OFF key
remains on.
5. Starting with the number 1 key, press and release
each number key in the following order (1-9, then 0).
The number that causes the illuminated ON·OFF key
to blink is the first number of the code. As you find
each number of the code, write them down for
future reference.
Note: All TV codes begin with the number 1; all VCR and DVR codes begin with the number
2; all DVDs, the number 3; all AUDIO, the number 4; all satellite receivers and cable boxes, the
number 5; all HDTVs, the number 7.
6. Repeat step 5 until you have retrieved all four
numbers in the code.
7. After the fourth number is retrieved, the illuminated
ON·OFF key blinks briefly, then turns off.
8. To exit the Code Retrieval mode at any time, press
and release the CLEAR key.
9. If you press an invalid key during the Code Retrieval
process, the remote will not respond. If you do not
press a valid Code Retrieval key, Code Retrieval
times out after 15 seconds. The illuminated ON·OFF
key blinks four times, and then turns off.
SAT·CBL CODE VCR CODE
TV CODE AUDIO CODE
Using the Remote to Control Your Components
Because this remote controls more than one component, you must first "tell" the remote
which component you wish to operate. That means, if you wish to operate your TV, you
must first press the TV key to put the remote in the TV mode.
The remote stays in the chosen mode until you change it. If your remote is in TV
mode, you must change the mode in order to operate other components. For example,
if you are in VCR mode and you wish to turn off your TV, you must press the TV key
first before pressing the ON·OFF key.
RCR812ƒ.indd 8-9 RCR812ƒ.indd 8-9
DVD CODE
DVR CODE
8
Volume Punch Through
Volume Punch Through allows the VOL+, VOL- and MUTE keys, when pressed in
VCR, DVD, DVR, SAT and CABLE modes, to "punch through" to either TV or AUDIO,
whichever was accessed last. Volume Punch Through occurs automatically and allows
you to control the volume without exiting the current mode. (If the AUX key has been
programmed with a TV or AUDIO code, that must be considered when determining the
last active TV or AUDIO component used.)
Note: Volume Punch Though does not occur in cases where the component code has its
own volume/mute data, such as a satellite receiver with its own volume/mute control, or if
volume/mute data has been learned for this device.
Advanced Volume Punch Through
Volume Punch Through, as described above, occurs automatically. However, if you
want to specify whether the Volume Punch Through is directed to the TV or AUDIO
while in VCR, DVR, DVD, CD, SAT or HDTV STB modes, follow the steps below. This
option can also be enabled for an AUX key, if it is programmed with a VCR, DVR,
DVD, CD, SAT or HDTV STB.
1. Press and hold any component key programmed for VCR, DVR, DVD, CD, SAT, or
HDTV. The illuminated ON·OFF key turns on.
2. While holding down the component key, press and hold the VOL+ key. The
illuminated ON·OFF key turns off.
3. After holding down both keys for 3 seconds, the illuminated ON·OFF key turns on
and stays on. Release both keys.
4. Press and release the component key you want the Volume Punch Through to
be directed to from the selected mode (TV, AUDIO or AUX key). The illuminated
ON·OFF key flashes, then turns off.
Note: The component key pressed in step 4 must be programmed with a TV or AUDIO
component. If an invalid key is pressed, the illuminated ON·OFF key flashes four times, then
turns off.
5. Once you have programmed any component with a specified Volume Punch Through,
the Volume Punch Through for all other components will default to AUDIO. If you do
not want other components' Volume Punch Through to default to AUDIO, you must
manually program them, using steps 1-4.
Transport Key Punch Through
Transport Key Punch Through allows the transport keys (REVERSE, PLAY,
FORWARD, RECORD, STOP and PAUSE), when pressed in TV, SAT, CABLE and
AUDIO modes, to "punch through" to VCR, DVR or DVD/CD mode, whichever was
accessed last. Transport Key Punch Through occurs automatically and allows you to
use the transport keys without exiting the current mode. (For example, if the transport
keys were last used in DVD mode and accessed again after pressing the TV key, they
will punch through to the DVD. The default Transport Key Punch Through is set to
DVD for TV, SAT, CABLE and AUDIO.
Note: Transport Key Punch Through does not occur in cases where the component code has
its own transport key data, such as a satellite receiver with a built-in DVR.
Sleep Timer (Select Models Only)
This feature automatically turns off your TV at a duration you choose from 1 to 99
minutes. The Sleep Timer only works if you have found a code that controls your TV.
The timing mechanism for the Sleep Timer is built into your universal remote control.
To program the Sleep Timer, follow these steps.
Programming the Sleep Timer
1. Press and release the TV key.
2. Press and hold the SLEEP key for three seconds. The illuminated ON·OFF key
turns on.
3. Release the SLEEP key.
4. Using the number keys, enter the desired time in minutes (from 1-99 minutes).
To set the timer to a number under 10 minutes, first press 0 and then the desired
number (e.g., 05 for five minutes). The illuminated ON·OFF key blinks with each
keypress.
5. Once the second number is entered, the illuminated ON·OFF key turns off and the
Sleep Timer is now set.
Any keypress other than the number keys is ignored. If the sleep time is not
! TIP:
entered within 15 seconds after pressing the SLEEP key, the illuminated ON·OFF key
blinks four times and turns off, indicating the attempt to program the Sleep Timer has
been unsuccessful.
6. Leave the remote aimed at the TV. Once the Sleep Timer is set, you can continue
to use the remote without affecting the Sleep Timer. However, the remote must be
put back in TV mode and pointed at the TV to activate the Sleep Timer.
Note: If the ON·OFF key is pressed, the Sleep Timer is canceled.
9
3/4/05 11:47:49 AM 3/4/05 11:47:49 AM