Publicité
Liens rapides
ASME A112.18.1 / CSA B125.1
ICC/ANSI A117.1
Model/Modelo/Modèle
64020LF & 64920LF
Series/Series/Seria
SOLNA
™
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
WARNING: THIS FAUCET IS NOT TO BE USED WITH
PORTABLE DISHWASHERS! / ADVERTENCIA: ¡SESTA
LLAVE NO SE DEBE UTILIZAR CON MAQUINAS
LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE
DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF
SUR CE ROBINET!
For easy installation of your
Delta
faucet you will need:
®
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and
maintenance information.
Para instalación fácil de su llave
Delta
usted necesitará:
®
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
Pour installer votre robinet
Delta
facilement, vous devez:
®
• LIRE TOUTES les instructions avant de débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
www.brizo.com
HIGH-RISE, PULL-DOWN KITCHEN
71450
AND BAR / PREP, TOUCH FAUCETS
LLAVES DE AGUA – GRIFOS DE CUELLO
CISNE EXTRAÍBLES DE FUNCIÓN AL
TACTO PARA COCINA Y BAR/PREP
ROBINETS TACTILES À BEC HAUT
RÉTRACTABLE POUR ÉVIER DE CUISINE
ET DE BAR OU D'ÎLOT
Articles dont vous pouvez avoir besoin:
71450
1
You may need
Usted puede necesitar
6/1/12
Rev. D
Publicité
Manuels Connexes pour Brizo SOLNA Serie
Sommaire des Matières pour Brizo SOLNA Serie
- Page 1 • LEER TODOS los avisos, cuidados, e información de mantenimiento. Pour installer votre robinet Delta facilement, vous devez: ® • LIRE TOUTES les instructions avant de débuter; • LIRE TOUS les avertissements ainsi que toutes les instructions de nettoyage et d’entretien; 71450 www.brizo.com 6/1/12 Rev. D...
- Page 2 1-877-345-BRIZO (2749) (in the U.S. and Canada) or by writing to: this warranty applying except the duration of the warranty. This warranty is applicable to Brizo faucets manufactured after January 1, 1995.
- Page 3 RP71446▲ Bar Spout Assembly with Magnet Ensamble del Tubo de Salida RP71447▲ Kitchen Spout Assembly with Magnet Ensamble del Tubo de Salida ▲Specify Finish ▲Especifíque el Acabado ▲Précisez le Fini RP64560 RP60923 Sprayer Assembly (Black Only) Friction Spacer Ensamble de rociador Arandela de Fricción Pulvérisateur Rondelle de frottement...
- Page 4 Backflow Protection System Other useful accessories that may be purchased separately. Your Delta faucet pull-down spout incorporates a backflow protection system that ® Otros accesorios útiles que se pueden comprar por separado. has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
- Page 5 Top Mount Sinks / Instalación por Encima / Bâti supérieur 1 1/4" Min. From Center Line To Sink Bowl. 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette.
- Page 6 Under Mount Sinks / Instalación por Debajo / Sous le bâti 1 1/4" Min. From Center Line To Sink Bowl. 1 1/4" Mínimo. De la línea de centro para hundir el tazón de fuente. 1 1/4" ; Minimal. De la ligne centrale pour descendre la cuvette.
- Page 7 OPTIONAL / OPCIONAL / FACULTATIVE Optional Escutcheon Installation For optional installations using the 10 1/2" escutcheon, order RP64070 not Solenoid Installation supplied (specify finish). Assemble adapter (1) solenoid (2) together using clip (3). Then slide SHUT OFF WATER SUPPLIES. Slide escutcheon (1) and gasket (2) over tubes adapter/solenoid assembly onto tube (4) and snap on swing clip (5).
- Page 8 Hose Installation Screw the threaded fitting of hose (1) into spray head (2) to prevent the hose Push hose end (1) onto solenoid assembly outlet (2). Attach clip (3) from being pulled into the spout until you are ready to flush the lines. Insert over hoses as shown.
- Page 9 Wire Connections Wire extension (3), extending from faucet shank, is shipped with a protective Briefly touch the cold stop or other ground with hand to dissipate any static plastic cap (4). Remove this by grasping the plug and pulling off the cap. charge.
- Page 10 Place battery pack in a convenient location close to the floor. Connect battery cable (1) to battery box (2). Install 6 “AA” batteries (3) into the (Place flat on the floor for best performance and at least battery box (2). Important: DO NOT install batteries before making all 2"...
- Page 11 Water Line Connections Custom Fit Connections WARNING: Do not use pipe dope or other sealants Important: To ensure proper operation of your If you determine the PEX supply tubing for this on water line connections. plumbing it is essential to install these check faucet is too long and must be shorter to create an valve assemblies onto your supply stops.
- Page 12 Incorrect Installation Correct method Instalación Incorrecta Método Correcto Installation Incorrecte Bonne méthode Do not install sleeve Ensure cut is straight. upside down. No instale la manga Asegúrese que el corte Custom Fit Connections - Plastic Sleeve Installation Instructions boca abajo. esté...
- Page 13 Turn on hot and cold water supplies (1). Pull the hose assembly (2) out Install the spray head (1) and remove blue clip (2) from hose. Check all of the spout. Be sure to hold the end of the hose down into the sink connections at arrows for leaks.
- Page 14 Maintenance Cleaning and Care If faucet leaks from under handle or pulling directly back on stem. Replace cartridge Care should be given to the cleaning of this product. from spout outlet – Insert a small and reassemble. Although its finish is extremely durable, it can be WARNING: Failure to securely tighten bonnet screwdriver into slot (1) in button (2) and damaged by harsh abrasives or polish.
- Page 15 Cleaning the Screen / Filtro de Limpieza: / Nettoyage du filtre SHUT OFF WATER SUPPLIES. Check and clean screen (1) located in solenoid valve (2). CIERRE LOS SUMINISTROS DE AGUA. Compruebe y limpie la pantalla (1) situada en la válvula electromagnética (2). FERMEZ LES ROBINETS D’ALIMENTATION.
- Page 16 Solenoid Troubleshooting 1. If your spout flashes a red light on then off and then keeps repeating this, 3. If your LED base indicator is not displaying any lights, replace the batteries. a. Check to make sure the spout connector is attached to the spout and the wire If the spout still flashes a red light, please replace solenoid and electronics kit**.