Bluetooth ® Pairing - Hama Calypso Mode D'emploi

Note
• If the battery level is low when using the headset, a voice says
'Low Battery'. Connect the headset to a suitable USB port
using the charging cable.
5. Operation
Switching the headset off/on
• Press and hold the MFB button (4) for about 3 seconds until a
voice says 'Power ON' and the blue LED (5) flashes.
• To switch the device off, press and hold the MFB button (4) for
about 5 seconds until a voice says 'Power OFF' and the red
LED (5) flashes and goes out.
Note
The functions described in this section are only available for
Bluetooth -capable terminal devices.
®
5.1. Bluetooth pairing
®
Note – Pairing
• Make sure that your Bluetooth
and Bluetooth is activated.
®
• Make sure that your Bluetooth
visible for other Bluetooth
• For more information, please refer to the operating
instructions of your terminal device.
• The headset and the terminal device should not be any further
than 1 metre away from each other. The smaller the distance,
the better.
• Switch the headset on using the MFB button (4).
• Press and hold the MFB button (4) for about 5 seconds
until a voice says 'PAIRING' and the blue and red LEDs
flash alternatingly. The headset is searching for a Bluetooth
connection.
• Open the Bluetooth settings on your terminal device and wait
®
until Hama BTH CALYPSO appears in the list of Bluetooth
devices found.
• Select Hama BTH CALYPSO and wait until the headset is listed
as connected in the Bluetooth
Note – Bluetooth password
®
Some terminal devices require a password in order to connect to
another Bluetooth device.
®
• If your terminal device requests a password for connection
with the headset, enter 0000.
Note
• Once the connection has been established, a voice says,
„Your device is connected".
-capable terminal device is on
®
-capable terminal device is
®
devices.
®
settings on your terminal device.
®
Note
• If the connection attempt takes longer than 180 seconds to
complete, it is cancelled and the LEDs go out. In this case,
repeat the steps listed previously under 5.1 Bluetooth
pairing.
5.2. Automatic Bluetooth
pairing)
Note – Pairing
• Make sure that your Bluetooth
and Bluetooth
• Make sure that your Bluetooth
visible for other Bluetooth
• For more information, please refer to the operating
instructions of your terminal device.
• Switch the headset on using the MFB button (4). The blue LED
begins to flash and the headset automatically connects with the
last terminal device used.
Note
• Once the connection has been established, a voice says,
„Your device is connected".
• If the connection attempt takes longer than 180 seconds to
complete, it is cancelled and the LEDs go out. In this case,
repeat the steps listed previously under 5.1.
• It may be necessary to make settings on your terminal device
to enable automatic connection with the paired headset.
Note – Connection impaired
After the headset and terminal device have been paired, a
®
connection is established automatically. If the Bluetooth
connection is not established automatically, check the following:
• Check the Bluetooth
®
whether Hama BTH CALYPSO is connected. If not, repeat the
steps listed under 5.1. Bluetooth
• Check whether obstacles are impairing the range. If so, move
the devices closer together.
• The performance can also be affected by a weak battery.
5.3. Bluetooth
This headset can be connected with two Bluetooth
terminal devices simultaneously.
• First connect the headset with the first terminal device as described in 5.1.
• Then disable Bluetooth
• Next, connect the headset with the second terminal device as
described in 5.1.
• Activate Bluetooth
headset now connects to that terminal device automatically.
connection (after successful
®
-capable terminal device is on
®
is activated.
®
-capable terminal device is
®
devices.
®
settings of your terminal device to see
®
pairing.
®
multipoint connection
®
on that terminal device.
®
on the first terminal device once more. The
®
®
®
-enabled
®
3