Lux Tools A-GS-20/20T Notice Originale page 24

GB
Tips on hedge trimming
1
2
1. Trim the hedge to the desired height.
2. Rejuvenate the hedge by trimming it from the bot-
tom up in trapezoidal form.
3. Round off the upper edges of the hedge.
4. Slightly trim the bottom of the hedge.
Cleaning and maintenance
Cleaning
NOTICE! Risk of damage to the device!
Do not submerge the device in water when
cleaning it since this would damage the elec-
trics.
Error/Fault
Device does not work.
If you can't fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.
Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environ-
ment and human health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. Information on returning these items is
available from the seller. Sellers are required to
accept these items free of charge.
Batteries and rechargeable batteries, which
are not permanently installed in waste elec-
trical devices, must be removed prior to dis-
posal and must be disposed of separately.
Lithium batteries and battery packs in all systems
must only be retuned to a collection point when dis-
charged. Batteries must always be protected against
short circuits by covering the poles with adhesive
tape.
All end users are responsible for deleting any per-
sonal data stored on waste devices prior to their dis-
posal.
24
3
4
Cause
Battery not slotted in correctly?
Battery pack discharged?
Battery pack defective?
Is the device defective?
NOTICE! Risk of damage to the device!
Do not use any sharp or abrasive objects, or
aggressive cleaning agents.
Do not use cleaning solutions.
– Remove any coarse dirt.
– Clean the outside of the device with a damp cloth.
Oil cutting tool
– Clean cutting tool with brush. Then, spray oil on
all sides of the cutting tool.
Troubleshooting
DANGER! Risk of injury! Unprofessional
repairs may mean that your unit will no
longer operate safely. This endangers you
and your environment.
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Remedy
Slot battery into place.
► Charging the battery pack – p. 23
Contact your local vendor.
Disposal of the packaging
The packaging consists of cardboard and
correspondingly marked plastics that can
be recycled.
– Make these materials available for recy-
cling.
Technical data
Item number
Idle revolutions
Sound power level (L
WA
Sound pressure level (L
Vibrations**
Weight
Max. operating duration with a full
battery
Hedge trimmer
Cutting length
Border cutter
Cutting width
*) The specified values are emission values and do not necessarily represent
safe workplace values. Although there is a correlation between emission
and immission levels, this cannot be used to infer whether additional safety
measures are necessary or not. Factors which affect the current immission
levels at the workplace, include the type of room, other sources of noise,
e. g. the number of machines operating and other processes taking place in
the vicinity. Permitted workplace values can differ from country to country.
This information is designed to help the user to better assess the dangers
and risks. Determination of noise emission values in accordance with
EN 60335-1 & EN 62841-1.
**) The specified vibration emission value was measured in accordance with a
normed test procedure and can be used in order to compare one tool with
another. The specified vibration emission value can also be used for an
196026
-1
1200 min
)* 87 dB(A)
(K = 3 dB(A))
)* 66 dB(A)
PA
(K = 3 dB(A))
< 3,4 m/s²
(K = 1.5 m/s²)
2,4 kg
100 min
200 mm
100 mm