Publicité
Les langues disponibles
Les langues disponibles
CS27742_MB-400_IB 8/31/05 4:36 PM Page 8
Trimming Beards
Before you begin, comb your hair in the
direction that it grows so that the hairs
are at their maximun height and facing
in the same direction.
Determine how much hair you want to
cut and position the hair length selector
accordingly. Remember, until you are
familiar with using the trimmer, it's
always better to select a longer hair
setting initially in order not to trim too
much hair.
Turn the unit's power switch to ON, and
begin trimming.
When finished trimming, turn the unit's
power switch to OFF.
To Trim Beard Hair Length
Put trimmer
guard attachment
on.
Turn the trimmer
so the front of
the cutting unit is
facing away from you.
Start trimming under your chin and,
following your jawbone line, work toward
your ear and upper beard line using an
upward motion. Allow the trimmer guard
attachment to follow the contours of your
face. You may trim either against or with
the direction of beard growth, whichever
you prefer.
8
Get user manuals:
See SafeManuals.com
How to Use
To Define the Beard Line
Remove trimmer guard attachment.
Hold trimmer vertically with trimmer
cutting blades facing you.
Start with the edge of your beard line,
and with the cutting blades resting lightly
against your skin,
use motions
toward the edge
of beard line to
trim the beard
line to desired
location.
To Thin and Taper the Beard
Remove trimmer guard attachment.
Use the unit's
styling comb or
another small
comb and hold
the beard hairs
in place while
trimming.
Holding the trimer horizontally with the
cutting unit facing away from you, move
the trimmer along the length of the
comb.
Creating the "Stubble Look"
Trimmer guard
attachment
should be
on and set to
position 1
(1.5 mm) or
2 (2.5 mm).
Hold trimmer horizontally with the cutting
unit facing either up down.
Trim hairs using an upward or downward
motion, against or with the direction of
hair growth, whichever you prefer.
For an even
Trimming the Nape of Your
closer "stubble
Neck
look," remove
You will need a
the trimmer
hand mirror for
guard attachment
this operation if
and repeat
performing it
the previous two steps. Be careful not
alone. The mirror
to remove too much hair, creating a
is not neccessary
"blotchy" look.
if trimming is performed by a second
person.
Detail Trimming
Remove the trimmer guard attachment.
Use your fingers to lift the hair at the
Comb hairs outward so they are at their
base of your head up off the neck. Your
maximum height.
index finger should be covering the roots
Remove trimmer guard attachment.
of the hairs you are lifting to prevent
Turn the power
accidental removal by trimmer.
switch to ON and
Using your other hand, hold the trimming
begin trimming.
edge horizontally against the base of your
Turn trimmer OFF.
neck with the cutting unit facing up, and
move the trimmer along the length of the
neck until the unit touches your finger
To Trim Mustache
covering the hair roots at the base of
your head. Repeat this procedure for the
Place a finger on upper lip to extend hair
entire area of the neck. Be sure to move
away from skin.
the unit slowly when performing this
Trim hairs using an upward motion.
operation and to keep the hair roots at
After achieving desired length, use a
the base of your head out of the way of
downward motion to blend mustache
the trimmer.
hairs.
Use the hand mirror to inspect the results
NOTE: Use slow and light pressure. Too
of the operation and ensure all hairs
much pressure may trim off more hair
along the nape of the neck have been
than desired.
trimmed.
Turn trimmer OFF.
To Trim Sideburns
Comb sideburns following the direction
of your hair growth.
Be certain trimmer guard attachment
is on.
Hold trimmer vertically with front of
trimmer facing you.
Trim sideburns using a downward
motion.
Turn trimmer OFF.
9
Publicité
