NORDRIVE CLUB Instructions D'installation page 5

ASSEMBLY INSTRUCTIONS
Thank you for choosing a NORDRIVE® product.
For proper use, carefully read assembly instructions and verify that all necessary
components are present.
• In order to avoid damaging the vehicle roof, it is suggested that assembly and
disassembly should be done by 2 persons.
• The person in charge of mounting this item on the longitudinal original bars is also
responsible for controlling that all instructions have been followed scrupulously.
ASSEMBLY
• Before mounting, clean with a damp cloth the longitudinal original bars.
• The roof bars must be fi xed to the longitudinal original bars by using the screws and the
fi xing plates provided (fi g.1).
Use only the provided trims between the fi xing element and the original bars. Do not
use any other extra trim (rubber, plastic, or any other).
1. Unscrew the screws and remove the lower plates ( g.2).
2. Position the bars on the longitudinal original ones ( g.3A / g.3B), keeping the 2
fi xing screws externally (fi g.4).
3. Verify the distance between the 2 bars ( g.5), lateral centring ( g.6) and their
alignment ( g.7). If necessary, use a meter for exact measures.
4. Reposition the lower plates with the rubber facing upwards and screw on the bolts,
without tightening them ( g.8).
5. Adjust the width between the 2 screws keeping them as close as possible to the
longitudinal original bar ( g.9- ).
6. With the provided wrench tighten 5Nm the bolts (fi g.9- ).
7. Repeat the same procedure with the other ttings brackets.
8. The lower slots can be covered using the supplied rubber pro le. Cut pro le to size
and insert into the slots ( g.10).
• Upon each assembly operation, check that the loading bars and locking feet are tightly
fi xed to the longitudinal original bars. To check, push and pull bars and the fi tting
brackets to make sure that everything has been tightly locked in place (we recommend
carrying out this test at regular intervals and before loading the vehicle).
• Modifying any part of this product is strictly prohibited.
• For any particular instruction or restriction on the application of the carrier bars,
refer to the "Use and maintenance manual" of the vehicle. If any, carefully follow the
instructions in the manual.
• Any time the vehicle does not provide for assembly positions, maintain a distance of at
least 70 cm between loading bars.
• When transporting long loads, the distance between loading bars should never be less
than 60 cm.
• If the bar is equipped with a lock, it must be closed before driving.
• Some sunroofs may not open with bars installed, or else they may only open partially.
• Loads which are too large or long may hinder the complete opening of the rear vehicle
door.
SECURING LOADS
• Never exceed the maximum load indicated in assembly instructions. This limit is
however subject to the maximum load illustrated in the vehicle user and maintenance
manual. Always follow instructions for the lowest maximum load.
• Maximum load is intended as: bar weight + weight of any applicable accessories +
weight of load.
• Locking accessories applied to bars (Roof boxes, ski racks, bike racks, hooks...etc.) must
be the appropriate type for the model of bar being utilised.
• Always arrange the load crosswise with respect to the load carrier bars and in such a
way that the centre of gravity is always as low as possible.
• Load dimensions cannot be much larger than the width of the bars or than the length
of the vehicle. Overfl owing loads must comply with applicable laws.
• Position the load setting it as uniformly as possible.
• When carrying long objects, they must be tightly fastened to the vehicle both on the
rear and on the front.
• All untied and removable objects being transported must be removed before loading,
while mobile parts must be fastened down.
• Loads must be tightly fastened to bars with the use of appropriate tie belts or cords. Do
not use elastic ropes.
All manuals and user guides at all-guides.com
CAUTION
• These roof racks are specially designed for vehicles with OEM longitudinal tradition
bars.
• After having driven for a short journey and, later, at regular intervals, stop the vehicle
and check that the load is still safely set. If necessary, tighten the tie belts or the
attachment straps.
• Maximum load capacity: 100 kg.
RULES FOR SAFE DRIVING
• Roof racks must not jut out over the sides of the vehicle.
• Ensure that the load does not come into contact with the roof during travel.
• Surf boards and canoes must be tightly attached to the front and rear ends of the
vehicle with a non-elastic tie-strap.
• Drive at a speed appropriate for the load that is being transported, according to driving
conditions and the type of road, tra c and speed limits.
• Driving and braking characteristics and sensitivity to lateral wind are aff ected by the
load being transported.
• Remember that, with the bars installed, the height of the vehicle increases.
• When transporting vertical loads like bicycles, height can increase up to 130 cm. The
maximum height allowed is 400 cm from the ground.
• LAMPA S.p.A. is not responsible for damages to objects or people due to high speed,
incorrect driving or incorrect load positioning and fastening.
• The drives is totally responsible for its own and other other people security.
• This manual must be kept for future consultations.
• To know more about applications and accessories (box, ski-carriers, bicycle carrieres...)
that can be used on these bars, visit www.nordrive.it.
CARE AND MAINTENANCE
• For safety and fuel effi ciency reasons, we recommend removing the roof racks when not
carrying loads.
• When not being used, dismantle, clean and store the bars in a dry place.
• Screws, bolts and locking devices (if present) must be greased at regular intervals.
• If damaged or worn parts are detected, replace immediately or contact a retailer.
CAUTION
• It is important to take note of the serial number shown on the key or lock (if available).
In the event of loss, you can request a duplicate at the retailer where you made your
purchase.
3