Publicité
Type of speaker system
SP-CR500C
Center speaker (1)
Connections
Connecting the speaker cords to the speaker terminals
Black line
1. Remove the ending part of the vinyl covering from the cut.
2. Twist the tip of speaker cord and then insert it into the hole while
holding down the terminal lever.
Connecting the speaker to the amplifier
SP-CR500C
Center speaker
CENTER
SURROUND
SPEAKER
RIGHT LEFT
CAUTION:SPEAKER IMPEDANCE
Speaker terminals on the amplifier
SP-CR500S
Surround speaker (right)
All manuals and user guides at all-guides.com
SP-CR500S
Surround speakers (2)
Press
FRONT
SPEAKERS
SPEAKERS
RIGHT LEFT
8
Ð
16
SP-CR500S
Surround speaker (left)
Precautions for installation and daily use
● Do not reproduce sounds at so high a volume that they are distorted;
otherwise, the speakers may be damaged by internal heat buildup.
● When moving the speakers, do not pull the speaker cords;
otherwise, the speakers may fall over, causing damage or injury.
● The speakers are magnetically shielded to avoid color distortions on
TVs. However, if not installed properly they may cause color
distortions. So, pay attention to the following when installing the
speakers.
] When placing the speakers near a TV set, turn off the TV's main
power switch or unplug it before installing the speakers. Then
wait at least 30 minutes before turning on the TV's main power
switch again.
Some TVs may still be affected even though you have followed the
above. If this happens, move the speakers away from the TV.
Connecting the speaker system to the amplifier
Before connecting:
● Make sure to match the polarity (F and G) when connecting the
speaker cords.
● Turn off the power to the amplifier before connecting the speaker
system; otherwise, the speakers may be damaged.
● The impedance of each speaker is 8 K. If this does not match with
the speaker impedance range indicated on the amplifier, you cannot
connect this system to the amplifier.
● The maximum power handling capacity of the SP-CR500C and
SP-CR500S are 100 W.
Excessive input will result in abnormal noise and possible damage.
● Be sure to turn down the volume level on the amplifier to prevent
unwanted noise before performing following operations:
] Turning on or off other components
] Operating the amplifier
] Tuning FM stations
] Fast-forwarding a tape
] Continuously reproducing high frequency oscillation or high pitch
electronic sounds
] Connecting or disconnecting a microphone
● When using a microphone, do not aim it at the speakers or use it
near the speakers; otherwise, the howling which occurs may
damage the speakers.
● Before replacing the cartridge, always turn off the power both to the
amplifier and to the turntable; otherwise, the clicking noise may
damage the speakers.
Specification
SP-CR500C
Type
Speaker unit
Power Handling Capacity
Impedance
Frequency Range
Sound Pressure Level
Dimensions
Mass
Accessories
SP-CR500S
Type
Speaker unit
Power Handling Capacity
Impedance
Frequency Range
Sound Pressure Level
Dimensions
Mass
Accessories
Check to be sure you have the above supplied accessories.
If any of the items above is missing, contact your dealer immediately.
Design and specifications subject to change without notice.
–3–
English
: 1-way 2-speaker Bass-Reflex Type
(Magnetically-shielded type)
: 5.5 cm cone × 2
: 100 W
: 8 K
: 65 Hz – 20 000 Hz
: 83 dB/W·m
: 270 mm × 99 mm × 130 mm
(W × H × D)
: 1.2 kg
: 4 m × 1
: 1-way 2-speaker Bass-Reflex Type
(Magnetically-shielded type)
: 5.5 cm cone × 2
: 100 W
: 8 K
: 70 Hz – 20 000 Hz
: 82 dB/W·m
: 88 mm × 181 mm × 126 mm
(W × H × D)
: 0.9 kg each
: 10 m × 2
Publicité
