Publicité
Ξ
J1
TH
TH
J2
TH
TH
TH
J4
J11
J3
TST1
2
TST
J6
J7
English
U
PGRADING THE MEMORY OF THE
When upgrading the standard memory to expansion memory the
following information will be lost:
1. All users
2. All door groups
3. All floor groups
4. All history
Make a hard copy of all the above information before installation.
The ATS1830 memory expansion is a special option installed into
the ATS4000 control panel to increase the memory capacity as
detailed below.
Note: The ATS1830 is a 1M expansion.
D
ESCRIPTION
From
Control
Panel
Users
50
Door groups
10
Floor groups
10
History:
• Alarm system
100
events
• Access control
100
events
Français
M
ISE A NIVEAU DE LA MEMOIRE DE LA CENTRALE
La mise à niveau de la mémoire standard à l'aide de l'extension
entraîne la perte des informations suivantes :
1. Tous les utilisateurs
2. Tous les groupes de portes
3. Tous les groupes d'étages
4. Tout l'historique
J12
J15
J18
ATS4000
J17
EPROM
FLASH
RAM/IUM
1
J13
J14
J8
J9
J10
ATS4000
To
11,466
• Users 1 to 200 have
16 characters for user
name.
• Users 1 to 1000 have
up to a 10 digit PIN
number.
• Users 1 to 11,466 can
be cardholders.
128
64
1000
1000
ATS4000
T H1
T H2
T H3
T H4
J9
J8
1 C 2 C 3 C
4 C 5 C 6 C 7 C 8 C 9 C 1 0 C 11 C 12 C 1 3 C 1 4 C 1 5 C 1 6 C
I
M
NSTALLING THE
EMORY EXPANSION
1. The user database will be lost when memory expansion is
fitted. Make notes of programming in users, doors and floor
groups.
2. Ensure that the unit is powered down (mains and battery).
3. Carefully remove the memory expansion chip from its
packaging, taking extreme care that none of the pins on the
chip get bent.
4. Take note of the orientation of the chip. The notch on the
screen-print of the ATS1830 and the RAM socket must align
at the same end. This notch indicates PIN 1 (see figure).
Carefully insert the chip into the socket labeled "RAM" making
sure that all of the pins fit firmly in the socket and none are
bent under.
5. Re-check the orientation of the chip in the socket and then re-
apply power to the unit.
Measures should be taken to prevent static
!
discharge when installing this device. A
conductive wrist strap should be worn and
connected to 0 V/Earth of the unit. i.e. "BATT -" or
"AUX PWR -" terminal. If a wrist strap is
unavailable, touch a control panel 0 V terminal
before commencing and avoid touching the pins of
the chip as much as possible.
Extension de mémoire
Avant de procéder à l'installation, prenez note sur papier de toutes
les informations ci-dessus.
L'extension de mémoire ATS1830 est une option spéciale installée
dans la centrale ATS4000 afin d'accroître la capacité de mémoire
tel que cela est décrit ci-dessous.
Remarque : Le module ATS1830 est une extension de 1 Mo.
M
ATS1830
ODEL
EPROM
F LASH
R AM
1
ATS1250/1260
J1 9
J 20
J10
J11
J12
Memory expansion
J21
1
Publicité
