Télécharger Imprimer la page

Ovention MiSA-a12 Manuel D'installation, D'entretien Et D'utilisation page 33

Publicité

Les langues disponibles

Les langues disponibles

English
Shunt
Testing/Troubleshooting
DANGER! Completely shut down and unplug oven
before proceeding. Refer to "Shutdown" procedure.
• If the lever on shunt is in the
tripped position, reset the shunt.
- If the shunt will not reset,
remove the lead wire from the
C1 terminal and try to reset the
shunt.
- If the shunt still will not reset,
replace the shunt.
WARRANTY, EXCLUSIVE REMEDY:
Ovention, Inc. (Seller) warrants that the products it
manufactures (Products) will be free from defects in materials
and workmanship under normal use and service and when
stored, maintained, and installed in strict accordance with
factory recommendations. Seller's sole obligation to the person
or entity buying the Products directly from Seller (Customer)
under this warranty is the repair or replacement by Seller or
a Seller-authorized service agency, at Seller's option, of any
Product or any part thereof deemed defective upon Seller's
examination, for a period of: (i) the Warranty Duration from the
date of purchase by Seller or (ii) the Warranty Duration from
the date of Product registration in accordance with Seller's
written instructions, whichever is later. The "Warranty Duration"
shall mean a period of one (1) year or the periods set forth
below for specific Product components. Credit for Products
or parts returned with the prior written permission of Seller
will be subject to the terms shown on Seller's material return
authorization form. PRODUCTS OR PARTS RETURNED
WITHOUT PRIOR WRITTEN PERMISSION OF SELLER
WILL NOT BE ACCEPTED FOR CREDIT. Expenses incurred
by Customer in returning, replacing or removing the Products
will not be reimbursed by Seller. If the defect comes under the
terms of the limited warranty, the Products will be repaired
or replaced and returned to the Customer and the cost of
return freight will be paid by Seller. The remedy of repair or
replacement provided for herein is Customer's exclusive
remedy. Any improper use, alteration, repairs, tampering,
misapplication, improper installation, application of improper
voltage or any other action or inaction by Customer or others
(including the use of any unauthorized service agency) that in
Seller's sole judgment adversely affects the Product shall void
this warranty. The warranty expressly provided herein may
only be asserted by Customer and may not be asserted by
Customer's customers or other users of the Products; provided,
however, that if Customer is an authorized equipment dealer of
Seller, Customer may assign the warranty herein to Customer's
customers, subject to all of the limitations of these Terms, and in
such case, the warranty shall be exclusively controlled by Seller
in accordance with these Terms. THIS LIMITED WARRANTY
IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED
TO ANY IMPLIED WARRANTY OF NONINFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE EXPRESSLY DISCLAIMED.
Ninety (90) Day Parts-Only Warranty:
Replacement Parts
OVMISAM-0522
Replacement Procedure
NOTE: Refer to the illustration in the "Double Mini Circuit
1. Completely shut down and unplug the oven. Refer to the
"Shutdown" procedure in the OPERATION section.
2. Remove the left side panel. Refer to the "Removing the
Side Panels" procedure in this section.
3. Disconnect two (2) lead wires from the double mini circuit
breaker and three (3) lead wires from the shunt next to the
breaker.
C1 Terminal
4. Insert a flat blade screwdriver into the green locking tabs
on the double mini circuit breaker to release the breaker
and the shunt from the DIN rail.
NOTE: The double mini circuit breaker and the shunt must be
5. Install the new shunt by reversing the steps above.
Notwithstanding anything herein to the contrary, the limited
warranty herein will not cover components in Seller's sole
discretion such as, but not limited to, the following: damage
to touchscreens and conveyor belts from abuse or impact;
wear items such as air filters; damage to catalyst from use of
non-approved cleaning products; product misuse, tampering,
or misapplication; improper installation; lack of or improper
cleaning; or application of improper voltage.
LIMITATION OF LIABILITY:
SELLER WILL NOT BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY,
OR SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION
ANY LOST PROFITS, COSTS OF SUBSTITUTE PRODUCTS,
OR LABOR COSTS, ARISING FROM THE SALE, USE,
OR INSTALLATION OF THE PRODUCTS, FROM THE
PRODUCTS BEING INCORPORATED INTO OR BECOMING
A COMPONENT OF ANOTHER PRODUCT, OR FROM ANY
OTHER CAUSE WHATSOEVER, WHETHER BASED ON
WARRANTY (EXPRESSED OR IMPLIED) OR OTHERWISE
BASED ON CONTRACT, TORT, OR ANY OTHER THEORY
OF LIABILITY, AND REGARDLESS OF ANY ADVICE OR
REPRESENTATIONS THAT MAY HAVE BEEN RENDERED
BY SELLER CONCERNING THE SALE, USE, OR
INSTALLATION OF THE PRODUCTS, EVEN IF SELLER IS
AWARE OF THE POSSIBILITY OF SUCH DAMAGES. IN NO
EVENT WILL SELLER'S AGGREGATE LIABILITY ARISING
OUT OF OR RELATED TO THIS AGREEMENT EXCEED THE
TOTAL AMOUNTS PAID TO SELLER BY CUSTOMER FOR
THE PRODUCTS WITHIN THE THREE (3) MONTH PERIOD
IMMEDIATELY PRECEDING THE EVENT GIVING RISE TO
CUSTOMER'S CLAIM.
HEREIN REGARDING SELLER'S LIABILITY SHALL BE VALID
AND ENFORCEABLE NOTWITHSTANDING A FAILURE
OF ESSENTIAL PURPOSE OF THE LIMITED REMEDY
SPECIFIED IN THESE TERMS.
33
SERVICE PROCEDURES
Breaker" service procedure.
removed from the DIN rail together. Once they are off
the DIN rail, they can be separated.
LIMITED WARRANTY
THE LIMITATIONS SET FORTH

Publicité

loading

Produits Connexes pour Ovention MiSA-a12