Transportation And Storage; Cleaning And Maintenance - MSW HP 2000 Manuel D'utilisation

VIII. MACHINE OPERATION – BASICS
3 1. Hot air outlet / location for attaching accessories.
2. Trigger with temperature and air flow control [only applies to
HP 2000 (6220)]
1
4
3. Temperature control [only applies to: HP 2000 PRO (6221), HP
2
2000C-PRO (6222)]
4. Trigger with temperature and air flow control [only applies to:
HP 2000 PRO (6221), HP 2000C-PRO (6222)]
5
5. Power cable
Device operation
1. Set switch to „0" and insert the plug into an electricity socket.
2. Then turn on the device by setting the switch to 1, 2 or 3. See table below for information about the
temperature and air flow intensity for given settings of the switch (during initial use, the heat gun may
emit a small quantity of smoke. After a certain time this will cease). To set the air temperature use:
a. The switch marked with the number 2 on the picture [only applies to HP 2000 (6220)] - setting I or II.
b. The knob marked with the number 3 on the picture [only applies to HP 2000 PRO (6221)]. To
increase the temperature, turn the knob clockwise, and in the opposite direction – anticlockwise – to
reduce the temperature. In the first switch position, the temperature is constant at 80°C.
c. The „+" and „-" buttons at the back of the device [only applies to HP 2000C-PRO (6222)]. Press
„+" to increase the temperature and „-" to decrease the temperature. In the first switch position, the
temperature is constant at 50°C.
The table showing temperatures and air flow speeds for various settings
Model HP 2000
Parameter Temperature [°C] Air flow [l/min]
Settings I 350
Settings II 550
Settings III -
Model HP 2000C-PRO
Parameter Temperature [°C] Air flow [l/min]
Settings I 50
Settings II 70-600
Settings III 70-600
Attaching accessories
The set includes additional nozzles, which can be used for specific jobs. To attach additional nozzles, slide it
over the heat gun outlet nozzle.
Attention! If changing / attaching additional nozzles, make sure the device is cold and disconnect it from
the power source.
Cone nozzle Fish tail nozzle
10
HP 2000 PRO
Temperature [°C] Air flow [l/min]
300 80 350
500 80-600 350
- 80-600 500
300
300
500
Glass protection nozzle
Rev. 05.05.2017
A set of scrapers is also included. Mount them onto the handle (also included) between two nuts on the
stem of the handle.
Attention! After use, to cool the device, align it so that the outlet nozzle is pointing upwards. Do not
leave a hot device in the vicinity of flammable materials.
IX. TRANSPORTATION AND STORAGE
During transport, the machine should be protected from shaking, crashing and turning upside down. Store it
in a properly ventilated place with dry air and without any corrosive gas.
X. CLEANING AND MAINTENANCE
• Disconnect the machine from the electricity when cleaning it.
• Use cleaner without corrosive substances to clean surface.
• After cleaning, all parts should be able to dry before the machine is to be reused
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
• Never spray the device with water jets.
XI. CHECK REGULARLY THE DEVICE
Check regularly the machine for signs of damage. If the machine is damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the machine).
• If relevant, take a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. Avoid formulations like „the device doesn't ́ t heat up",
which may mean that it doesn't ́ t heat enough or even not at all. The more detailed your information,
the better customer service will be able to solve your problem rapidly and efficiently!
CAUTION: Never open the machine without the authorization of your customer service. This can lead
to a loss of warranty!
Rev. 05.05.2017
11