◈ Self Test
1. Make sure the paper roll has been installed properly.
2. Turn on the power while holding down the FEED button. The self-test begins.
3. The self-test prints the current printer status, providing the control ROM version and the
DIP switch setting.
4. After printing the current printer status, self-test printing will print the following, and
pause. (The PAPER LED light blinks.)
SELF-TEST PRINTING.
PLEASE PRESS THE FEED BUTTON.
5. Press the FEED button to continue printing. The printer prints a pattern using the built-in
character set.
6. The self-test automatically ends and cuts the paper after printing the following.
*** COMPLETED ***
7. After the self-test is complete, the printer returns to normal on-line status.
※ Note
The self-test lets you know if your printer is operating properly. It checks the print quality,
ROM version, and DIP switch settings.
◈ Specifications
Item
Printing Method
Dot Density
Printing Width
Characters per line (default)
Printing Speed *1)
Receive Buffer Size
SMPS Input Voltage
Printer
Frequency
SMPS Output Voltage
Temperature
Humidity
Mechanism Head Life *2)
Auto Cutter
Mechanism MCBF *2)
Paper Type
Roll Width
Roll Diameter
Paper
Paper Thickness
Paper Tube
※ Note
*1) Printing speed may be slower depending on the data transmission speed and the
combination of control commands.
*2) The above values are calculated under printing level 2 with recommended paper at
normal temperature.
The values may vary with environment temperature, printing level, etc.
◈ Serial (RS-232C) Fixed Interface Model Windows Driver
Installation: IFA-S TYPE
1. After running the product installation CD, run the Thermal Printer > SRP-350 > Drivers
> Windows Driver > Drivers Folder > Win SRP-350_Vx.x.x.exe file.
2. In the opening installation window, click on Next.
3. In the Ready to Install the Program window, click on Install.
4. In the Select Port Type window, select one Serial Port and click Next.
5. In the Question window, select Yes and the computer will reboot.
6. After rebooting, open Start > Settings > Printers & Fax > BIXOLON SRP-350 Icon >
Right-Click > Properties.
7. In the Properties window, select the Port tab and click on the Port Settings. Check to see
that the information is identical to the self-test results after installation.
Details
Thermal Line Printing
180 X 180 dpi (7dots/mm)
72 mm
42 (Font A)
56 (Font B)
46.2 lines/sec
150 mm/sec
4K Bytes
100~240 VAC
50/60 Hz
24 VDC
0 ~ 45 ℃ (Operating)
-10 ~ 50 ℃ (Storage)
30 ~ 80 % RH (Operating)
10 ~ 90 % RH (Storage)
Except for paper
150Km
1,500,000 Cuts
37,000,000 Lines
Paper Roll
80 mm
Max 83mm
0.062~0.075 mm
Inner: Ø12mm (0.47")
Outer: Ø18mm (0.71")
(Figure 1.)
8. In the Properties window, after selecting the General tab, click on Print Test Page to
confirm that printing is normal.
◈ Parallel (IEEE1284) Fixed Interface Model Windows Driver
Installation: IFA-P TYPE
1. After running the product installation CD, run the Thermal Printer > SRP-350 > Drivers
> Windows Driver > Drivers Folder > Win SRP-350_Vx.x.x.exe file.
2. In the opening installation window, click on Next.
3. In the Ready to Install the Program window, click on Install.
4. In the Select Port Type window, select one Parallel Port and click Next. (Refer to Figure
1.)
5. In the Question window, select Yes and the computer will reboot.
6. After rebooting, open Start > Settings > Printers & Fax > BIXOLON SRP-350 Icon >
Right-Click > Properties.
7. In the Properties window, after selecting the General tab, click on Print Test Page to
confirm that printing is normal.
◈ USB Fixed Interface Model Windows Driver Installation:
IFA-U TYPE
1. After running the product installation CD, run the Thermal Printer > SRP-350 > Drivers
> Windows Driver > Drivers Folder > Win SRP-350_Vx.x.x.exe file.
2. In the opening installation window, click on Next.
3. In the Ready to Install the Program window, click on Install.
4. In the Select Port Type window, select USB and click Next. (Refer to Figure 1.)
5-1. If using Windows 98/ME:
① After completing the installation procedures, reboot the computer.
② After rebooting, turn the printer power off and back on.
③ After the New Hardware Detected window appears, continue to click Next to install the
USB drive, and then reboot the computer once more.
5-2. If using Windows 2000:
① After the Information window appears, turn the printer off and back on and click Yes.
② After installation is complete, reboot the computer.
5-3. If using Windows XP:
① After the Information window appears, turn the printer off and back on and click Yes.
② After the New Hardware Detected window appears, continue to click Next to install the
USB drive, and then reboot the computer.
※ Note
When the digital registration message appears during installation, click on either OK or
Continue Anyway.
6. After rebooting, open Start > Settings > Printers & Fax > BIXOLON SRP-350 Icon >
Right-Click > Properties.
7. In the Properties window, after selecting the General tab, click on Print Test Page to
confirm that printing is normal.
◈ Ethernet Fixed Interface Model Windows Driver Installation:
IFA-E TYPE
Refer to the user manual regarding separate Ethernet interface cards.(refer to the CD)
◈ WEEE (Waste Electrical and Electric Equipment)
This marking shown on the product or its literature, indicates that is should not be
disposed with other household wastes at the end of its working life, To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe recycling. Business
users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
☎ BIXOLON Co., Ltd.
● Website http://www.bixolon.com
● Korea Headquarters
th
(Add) Digital Empire Block A, 5
Floor, 980-3 Yeongtong-dong, Yeongtong-gu, Suweon-shi,
Gyeonggi-do, Korea 443-813
(Tel.) +82-31-218-5500
● U.S. Office
(Add) BIXOLON America Inc., 1210 E. 223rd St., #330, Carson, CA 90745
(Tel.) +1-858 764 4580
● Germany Office
(Add) BIXOLON Germany GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf
(Tel.) +49 (0)211 68 78 54 0