BIXOLON SRP-500 Guide D'installation

KN06-00002A (Rev.1.7)
◈ Information
This Installation Guide includes a brief outline of information necessary for
product installation. For more detailed installation information, please refer to the
user manual in the enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a logo download tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions
and quality of all our products. In following, product specifications and/or user
manual content may be changed without prior notice.
◈ Components
Cable Cover
SRP-500
AC/DC Adaptor
◈ Connecting the cables
1. Plug the power cord into the AC Adaptor, and then plug the AC Adaptor into
the power connector of the printer
2. Turn off the printer and the host ECR (host computer).
3. Check the interface cable (Serial, Parallel, USB), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the
printer.
Interface
connector
Interface cable
(Serial/Parallel/USB)
◈ Installing the Ink Cartridge
1. Turn on the printer.
2. Remove new ink cartridge from the pouch and remove the tape affixed to the
front side.
3. Open front cover of the printer and pull the cartridge holder forward.
4. Take out old ink cartridge(s) and place new cartridge(s) into carriage. Hold
round tab to ensure clean installation.
Black cartridges go into left carriage, and color cartridges go into right
carriage. Tab faces front of printer.
5. Close cartridge holder(s) and front cover.
Tab
Tape
Metallic connector
area
※ Note
The ink drop counter is automatically reset when the ink cartridge is installed.
Paper Roll Ink Cartridge
Power cord Installation Guide
Drawer kick-out
connector
Power connector
Adaptor
Power cord
Drawer kick-
out cable
Front cover
Cartridge holder
Printer Installation Guide
INKJET PRINTER
◈ Installing the Paper Roll
◈ Using the Operation Panel
• Power (LED)
Procuct Installation CD Procuct Installation CD Procuct Installation CD
When turning on the power, a green LED will be lit.
CD
• Error (LED)
When an error occurs, a red LED will be lit. (e.g. no paper,
cover ajar, etc.)
• Cartridge (LED)
Check the status of the right cartridge with the right LED, and
the left cartridge, with the left LED. For monochrome, the left
LED is used. The left cartridge is black, and the right cartridge is
color.
• Clean (Button)
Use this button to clean the ink cartridge heads.
• Feed (Button)
Press the FEED button once to discharge extra paper. Holding
down the FEED button will discharge paper continuously until
the button is released.
◈ Setting the DIP Switches
Changing Dip Switch settings must be done when the printer is off. Any changes
done while the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW Function
1-1
Emulation
1-2
1-3 Auto Cutter
1-4 Cartridge
1-5 Density
1-6 Special Function
1-7 Near-End Sensor Status
1-8 Undefined
• DIP Switch 2
SW Function
2-1 Data Receive Error
2-2
2-3 Handshaking
2-4 Data Length
2-5 Parity Check
2-6 Parity Selection
2-7
Baud Rate Selection
2-8
2. Parallel / USB Interface
• DIP Switch 1
SW Function
1-1
Emulation
1-2
1-3 Auto Cutter
1-4 Cartridge
1-5 Density
1-6 Special Function
1-7 Near-End Sensor Status
1-8 Undefined
SRP-500
1. Open the rear cover.
2. Insert a new paper roll, making sure to
align it properly.
3. Pull out a small amount of paper, and
close the rear cover.
ON OFF
Refer to the following table 1
Enable Disable
One cartridge Two cartridges
Bold Normal
Enable Disable
Enable Disable
Undefined
ON OFF
Print ? Ignore
Reserved
DTR/DSR XON/XOFF
7 bits 8bits
Enable Disable
EVEN ODD
Refer to the following table 2
ON OFF
Refer to the following table 1
Enable Disable
One cartridge Two cartridges
Bold Normal
Enable Disable
Enable Disable
Undefined
Default
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF