Makita GD0800C Manuel D'instructions page 4

Masquer les pouces Voir aussi pour GD0800C:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 6
ENGLISH
1 Tighten
2 Loosen
3 Wrench 19
SPECIFICATIONS
Model
Collet size .............................................................................. ø8 mm max.
Max. wheel point diameter .................................................... ø25 mm
-1
No load speed (min
) ........................................................... 7,000 – 28,000
Overall length ........................................................................ 371 mm
Net weight ............................................................................. 1.6 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Always use eye and ear protection. Other
personal protective equipment such as dust
mask, gloves, helmet and apron should be
worn when necessary. If in doubt, wear the
protective equipment.
2. Use only wheels with correct size and wheels
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool's nameplate.
3. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
4. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
5. Before using the tool on an actual workpiece,
test run the tool at the highest no load speed
for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wob-
bling that could indicate poor installation or a
poorly balanced wheel. Check the tool to
determine the cause.
6. Check that the workpiece is properly sup-
ported.
4
All manuals and user guides at all-guides.com
Explanation of general view
4 Wrench 13
5 Collet nut
7. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a ''live'' wire will make exposed
metal parts of the tool ''live'' and shock the
operator.
8. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
9. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other per-
sons or flammable materials.
10. Pay attention that the wheel continues to
rotate after the tool is switched off.
11. Hold the tool firmly.
12. Keep hands away from rotating parts.
13. Do not leave the tool running. Operate the tool
only when hand-held.
14. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
ENB044-2
burn your skin.
15. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
16. Do not use the tool on any materials contain-
ing asbestos.
17. Do not use water or grinding lubricant.
18. Do not use this tool as cutter.
19. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first discon-
nect the tool from the main supply (use non
metallic objects) and avoid damaging internal
parts.
SAVE THESE INSTRUCTIONS.
6 Switch lever
7 Speed adjusting dial
GD0800C
GD0810C
ø8 mm max.
ø50 mm
1,800 – 7,000
371 mm
1.7 kg

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Gd0810c

Table des Matières